Yamaha F-20B Скачать руководство пользователя | Manualshive

Страница: 51 / 94

background image

Operation

44

if necessary. Consult your Yamaha
dealer if the cause for the low oil
pressure alert cannot be found.

[ECM01832]

EMU36532

Checks after engine warm up

EMU36542

Shifting

While the boat is tightly moored, and without
applying throttle, confirm that the engine
shifts smoothly into forward and reverse, and
back to neutral.

EMU36981

Stop switches



Turn the main switch to “

”, or press the

engine stop button and make sure the en-
gine stops.



Confirm that removing the clip from the en-
gine shut-off switch stops the engine.



Confirm that the engine cannot be started
with the clip removed from the engine
shut-off switch.

EMU34563

Shifting

WARNING

EWM00181

Before shifting, make sure there are no
swimmers or obstacles in the water near
you.

NOTICE

ECM01611

Warm up the engine before shifting into
gear. Until the engine is warm, the idle
speed may be higher than normal. High
idle speed can prevent you from shifting
back to neutral. If this occurs, stop the
engine, shift to neutral, then restart the
engine and allow it to warm up.

To shift out of neutral
1. Pull the neutral interlock trigger up (if

equipped).

2. Move the remote control lever / gear

shift lever firmly and crisply forward (for
forward gear) or backward (for reverse
gear) [about 35



(a detent can felt) for re-

mote control models]. Be sure to check
that the tilt lock lever is in the lock/down
position (if equipped) before operating in
reverse.

1. Neutral interlock trigger

ZMU05541

6AG-9-79-1E0.book 44 ページ２０１４年１１月１０日　月曜日　午後４時８分

«
...
49
50
51
52
53
...
»

Содержание F-20B































































































Отзывы:

Нет отзывов

Похожие инструкции для F-20B

Бренд: Xtant Страницы: 2

Бренд: Parasound Страницы: 16

Бренд: Samson Страницы: 16

Бренд: Accel Instruments Страницы: 2

Бренд: JBL Страницы: 22

Бренд: Laney Страницы: 14

Бренд: Lab.gruppen Страницы: 13

Бренд: JBL Страницы: 4

Бренд: JBL Страницы: 4

Бренд: JBL Страницы: 4

Бренд: JBL Страницы: 44

Бренд: JBL Страницы: 23

Бренд: JEFF ROWLAND Страницы: 27

Бренд: Warwick Страницы: 1

Бренд: Warwick Страницы: 4

Бренд: QUAD Страницы: 12

Бренд: RAM Страницы: 13

ZeroUno PLUS ULTRA

Бренд: Canever Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды