Yamaha F-20B Скачать руководство пользователя | Manualshive

Страница: 64 / 94

background image

Maintenance

57

right), put it on a cushion after draining
the engine oil.



Do not place the outboard motor on its
side before the cooling water has
drained from it completely, otherwise
water may enter the cylinder through
the exhaust port and cause engine trou-
ble.



Store the outboard motor in a dry, well-
ventilated place, not in direct sunlight.

EMU28306

Procedure

EMU32027

Flushing in a test tank

NOTICE

ECM00302

Before starting the engine, make sure to
supply water to the cooling water passag-
es. Otherwise, the engine could overheat
and be damaged.

1. Dismount the outboard motor from the

boat. For further details, see page 55.

2. Wash the outboard motor body using

fresh water.

NOTICE:

Do not spray wa-

ter into the air intake.

[ECM01841]

For fur-

ther information, see page 59.

3. Disconnect the fuel line from the out-

board motor.

4. Remove the top cowling and silencer

cover/cap, if equipped. Remove the pro-
peller. For further details, see page 70.

5. Position the outboard motor on a water

tank. For further details, see page 29.

6. Fill the tank with fresh water until the

anti-cavitation plate is immersed in wa-
ter.

NOTICE:

If the fresh water level is

below the level of the anti-cavitation
plate, or if the water supply is insuffi-
cient, engine seizure may occur.

[ECM00292]

7. Cooling system flushing is essential to

prevent the cooling system from clog-
ging up with salt, sand, or dirt. In addi-
tion, fogging/lubricating of the engine is
mandatory to prevent excessive engine
damage due to rust. Perform the flush-
ing and fogging at the same time.

WARNING! Do not touch or remove
electrical parts when starting or dur-
ing operation. Keep hands, hair, and
clothes away from the flywheel and
other rotating parts while the engine
is running.

[EWM00092]

8. Run the engine at a fast idle for a few

minutes in neutral position.

9. Just prior to turning off the engine, quick-

ly spray “Fogging Oil” alternately into
each carburetor or the fogging hole of
the silencer cover, if equipped. When
properly done, the engine will smoke ex-
cessively and almost stall.

10. Remove the outboard motor from the

test tank.

11. Install the silencer cover/cap of fogging

hole (if equipped) and top cowling.

12. If the “Fogging Oil” is not available, run

the engine at a fast idle until the fuel sys-
tem becomes empty and the engine

1. Water surface
2. Lowest water level

ZMU02051

1

2

6AG-9-79-1E0.book 57 ページ２０１４年１１月１０日　月曜日　午後４時８分

«
...
62
63
64
65
66
...
»

Содержание F-20B































































































Отзывы:

Нет отзывов

Похожие инструкции для F-20B

Бренд: B&K Страницы: 9

'65 TWIN REVERB

Бренд: Fender Страницы: 7

Бренд: D.A.S. Страницы: 11

Бренд: X4-TECH Страницы: 16

Бренд: B&K Страницы: 64

Бренд: Bad Cat Страницы: 7

ProX 840.4 COMP

Бренд: µ-Dimension Страницы: 12

Бренд: Rockford Fosgate Страницы: 40

EEA-PAM-591-A-10

Бренд: Danfoss Страницы: 19

Бренд: Shure Страницы: 34

Бренд: DAPAudio Страницы: 18

Бренд: Samson Страницы: 24

Бренд: Crest Audio Страницы: 2

Бренд: Crate Страницы: 8

Guy Pratt INTERSTELLAR-600

Бренд: Ashdown Страницы: 27

Бренд: Wilson Electronics Страницы: 12

Бренд: Luxman Страницы: 18

Бренд: Tascam Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды