manualshive.com logo in svg

Yamaha F-20B, Руководство пользователя

Поделиться
Скачать
Yamaha F-20B Скачать руководство пользователя страница 43

Operation

36

EMU34783

Checking power tilt system

WARNING

EWM01971

Never get under the lower unit while it
is tilted, even when the tilt support
knob is locked. Severe injury could oc-
cur if the outboard motor accidentally
falls.

Body parts can be crushed between the
motor and the clamp bracket when the
motor is trimmed or tilted.

Be sure no one is near the outboard
motor before performing this check.

1. Check the power tilt unit for any sign of

oil leaks.

2. Operate each of the power tilt switches

to check that all switches work.

3. Tilt the outboard motor up and check

that the tilt rod is pushed out completely.

4. Check that the tilt rod is free of corrosion

or other flaws.

5. Tilt the outboard motor down. Check that

the tilt rod operates smoothly.

EMU36583

Battery

Check that the battery is in good condition,
and fully charged. Check that the battery
connections are clean, secure and covered
by insulating covers. The electrical contacts
of the battery and cables must be clean and
properly connected or the battery will not
start the engine.
Refer to the battery manufacturer’s instruc-
tions for checks for your particular battery.

EMU2743A

Filling fuel 

WARNING

EWM01831

Gasoline and its vapors are highly flam-
mable and explosive. Always refuel ac-
cording to this procedure to reduce the
risk of fire and explosion.

Gasoline is poisonous and can cause
injury or death. Handle gasoline with
care. Never siphon gasoline by mouth.
If you should swallow some gasoline or
inhale a lot of gasoline vapor, or get
some gasoline in your eyes, see your
doctor immediately. If gasoline spills
on your skin, wash with soap and wa-
ter. If gasoline spills on your clothing,
change your clothes.

1. Be sure the engine is stopped.
2. Disconnect the fuel line from the fuel

tank and tighten the air vent screw on
the fuel tank cap.

1. Tilt rod

6AG-9-79-1E0.book  36 ページ  ２０１４年１１月１０日　月曜日　午後４時８分

Содержание F-20B































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды