manualshive.com logo in svg

Yamaha F-20B, Руководство пользователя

Поделиться
Скачать
Yamaha F-20B Скачать руководство пользователя страница 30

Components

23

juster.

EMU26254

Trim tab

WARNING

EWM00841

An improperly adjusted trim tab could
cause difficult steering. Always test run
after the trim tab has been installed or re-
placed to be sure steering is correct. Be
sure you have tightened the bolt after ad-
justing the trim tab.

The trim tab should be adjusted so that the
steering control can be turned to either the
right or left by applying the same amount of
force.
If the boat tends to veer to the left (port side),
turn the trim tab rear end to the port side “A”
in the figure.
If the boat tends to veer to the right (star-
board side), turn the trim tab end to the star-
board side “B” in the figure.

EMU26263

Trim rod (tilt pin)

The position of the trim rod determines the
minimum trim angle of the outboard motor in

relation to the transom.

EMU30531

Tilt lock mechanism

The tilt lock mechanism is used to prevent
the outboard motor from lifting out of the wa-
ter when in reverse gear.

To lock it, set the tilt lock lever in the lock po-

1. Trim tab
2. Bolt

Bolt tightening torque:

8 Nm (0.82 kgf-m, 5.9 ft-lb)

ZMU05524

1

2

B

A

1. Tilt lock lever (Lock / tilt-down)

1. Tilt lock lever (Release / tilt-up)

ZMU05525

ZMU05526

1

ZMU05631

1

6AG-9-79-1E0.book  23 ページ  ２０１４年１１月１０日　月曜日　午後４時８分

Содержание F-20B































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды