Yamaha F-20B Скачать руководство пользователя страница 42

Страница: 42 / 94

Operation

pears milky or dirty.

EMU27154

Engine



Check the engine and engine mounting.



Look for loose or damaged fasteners.



Check the propeller for damage.



Check for engine oil leaks.

EMU36494

Flushing device

Check that the flushing device’s garden hose
connector is securely screwed on to the fit-
ting on the bottom cowling.

NOTICE:

If the

garden hose connector is not properly
connected, cooling water can leak out
and the engine can overheat during oper-
ation.

[ECM01802]

EMU36956

Install top cowling

1. Be sure that the cowling lock lever is re-

leased.

2. Be sure that the rubber seal is seated all

the way around the top cowling.

3. Place the top cowling on the bottom

cowling.

4. Check to be sure the rubber seal is seat-

ed correctly between the top cowling
and the bottom cowling.

5. Move the cowling lock lever to lock the

top cowling as shown.

NOTICE:

If the

top cowling is not installed correctly,
water spray under the top cowling
can damage the engine, or the top
cowling can blow off at high speeds.

[ECM01992]

After installing, check the fitting of the top
cowling by pushing it with both hands. If the
top cowling is loose, have it repaired by your
Yamaha dealer.

1. Lower mark
2. Oil dipstick
3. Upper mark

1. Fitting

ZMU0

041

ZMU06172

2. Flushing device

ZMU06136

6AG-9-79-1E0.book 35 ページ２０１４年１１月１０日　月曜日　午後４時８分

Содержание F-20B































































































Результаты поиска

Содержание F-20B

Отзывы:

Бренды по названию

Популярные бренды

Yamaha F-20B, Руководство пользователя

Результаты поиска

Содержание F-20B

Отзывы:

Бренды по названию

Популярные бренды