VX-6E O
PERATING
M
ANUAL
88
S
ET
(
M
ENU
)
M
ODE
S
ET
M
ODE
I
TEM
1 [APO]
2 [AR BEP]
3 [AR INT]
4 [ARS]
5 [ATT]
6 [BCLO]
7 [BEEP]
8 [BELL]
9 [BP LVL]
10 [BNK NM]
11 [BSY.LED]
12 [CH CNT]
13 [CLK.SFT]
14 [CW ID]
15 [CWTRNG]
16 [DC VLT]
17 [DCS CD]
18 [DCS RV]
19 [DIMMER]
20 [DMR.WRT]
21 [DT A/M]
22 [DT SET]
23 [EAI]
24 [EAI.TMR]
25 [EDG.BEP]
26 [EMG S]
27 [HLF.DEV]
28 [HM/RV]
29 [INT CD]
30 [INT MD]
31 [INT.A/M]
32 [INT.SET]
33 [LAMP]
34 [LED LT]
35 [LOCK]
36 [M/T-CL]
37 [MCGAIN]
38 [MW MD]
39 [NAME]
40 [NM SET]
F
UNCTION
Setting of the Automatic Power-Off feature.
Selects the Beep option during ARTS operation.
Selects the Polling Interval during ARTS operation.
Enables/Disables the Automatic Repeater Shift function.
Enables/Disables the Receiver Front-end (10 dB) Attenuator.
Enables/Disables the Busy Channel Lock-Out feature.
Enables/Disables the keypad beeper.
Selects the number of CTCSS/DCS Bell ringer repetitions.
Adjust the Beep volume level.
Stores Alpha-Numeric “Tags” for the Memory Group.
Enables/Disables the BUSY LED while the Squelch is open.
Selects the Channel Counter Search Width.
Shifting of the CPU clock frequency.
Programs and activates the CW Identifier (used during ARTS op-
eration).
Enables/Disables the CW Training feature and selects the sending
speed of the Morse Code.
Indicates the DC Supply Voltage.
Setting of the DCS code.
Enables/Disables “Inverted” DCS code decoding.
Setting of the Display brightness level.
Enables/Disables over-written the Direct Memory Recall Channel
while operating on the Direct Memory Recall Channel.
Enables/Disables the DTMF Autodial feature.
Programming of the DTMF Autodialer.
Enables/Disables the Emergency Automatic ID (EAI) Feature.
Setting of the Emergency Automatic ID (EAI) operating mode and
its Transmit Time.
Enables/Disables the Band-edge beeper while selecting the fre-
quency via the DIAL knob.
Selects the alarm(s) utilized when the Emergency function is en-
gaged.
Reducing the Deviation level by 50 %.
Selects the Primary function of the [HM/RV(EMG)R/H] key.
Selects the Access Number (DTMF digit) for WIRES
TM
operation.
Selects the Internet Link Connection mode.
Enables/Disables DTMF Autodialer feature while operating on the
Internet Connection feature.
Selects the memory register for an Access Number (DTMF code)
for non-WIRES™ Internet Link System access.
Selects the LCD/Keypad Lamp mode.
Illuminates the STROBE glows continuously in white.
Selects the Control Locking lockout combination.
Selects the MONI switch (just below the PTT switch) function.
Adjust the microphone gain level.
Selects the method of selection of channels for Memory Storage.
Toggles the display indication between “frequency” and the
channel’s “Alpha/Numeric Tag.”
Stores Alpha-Numeric “Tags” for the Memory channels.
A
VAILABLE
V
ALUES
(
D
EFAULT
:
B
OLD
I
TALIC
)
OFF
/ 30MIN / 1HOUR / 3HOUR /
5HOUR / 8HOUR
IN RNG
/ ALWAYS / OFF
25 SEC
/ 15 SEC
ON
/ OFF
OFF
/ ON
OFF
/ ON
ON
/ OFF
OFF
/ 1 / 3 / 5 / 8 /
CONT (Continuous ringing)
LVL 1 - LVL 9 (
LVL 5
)
---
ON
/ OFF
±5 MHz
/ ±10 MHz /
±50 MHz / ±100 MHz
OFF
/ ON
---
OFF
/
4WPM-13WPM / 15WPM /
17WPM / 20WPM / 24WPM /
30WPM / 40WPM
(20CPM-65CPM (5CPM multiples) /
75CPM / 85CPM / 100CPM /
120CPM / 150CPM / 200CPM)
---
104 standard DCS codes (
023
)
DISABLE
/ ENABLE
LVL 0 - LVL 12 (
LVL 7
)
OFF
/ ON
MANUAL
/ AUTO
---
OFF
/ ON
INT. 1M through INT.10M /
INT.15M / INT.20M / INT.30M /
INT.40M / INT. 50M
CON. 1M through CON.10M /
CON.15M / CON.20M / CON.30M /
CON.40M / CON. 50M (
CON.5M
)
OFF
/ ON
BP+STR
/ BEAM / BP+BEM / CW /
BP+CW / BEEP / STROBE
OFF
/ ON
REV
/ HOME
DTMF 1
- DTMF F
SRG
/ FRG
MANUAL
/ AUTO
---
KEY
/ CONT / OFF
---
KEY / DIAL /
K+D
/ PTT /
P+K / P+D / ALL
MONI / T-CALL
Ú
1
LVL 1 - LVL 9 (
LVL 5
)
NEXT
/ LOWER
FREQ
/ ALPHA
--
Ú
1: Depends on the transceiver version.
Содержание VX-6E
Страница 86: ...VX 6E OPERATING MANUAL 84 MISCELLANEOUS SETTINGS NOTE ...
Страница 110: ...VX 6E OPERATING MANUAL 108 NOTE ...
