Yaesu FT DX 9000MP CONTEST - DATA MANAGEMENT OPERATION, Руководство по эксплуатации

Страница: 65 / 180

Page 63 FT
DX
9000MP O
PERATION
M
ANUAL
C
HANGING THE
S
PEAKER
O
UTPUT
C
ONFIGURATION
If you use the FT
DX
9000MP internal speaker without using the FPS-9000H ’s speaker, an internal switch and the menu
allow you to configure the way audio is fed to the two ingernal speakers (either “stereo” or “monaural” modes are avail-
able).
A A A A A
D D
D D DVICE
VICE
VICE VICE VICE
At the factory, the audio signals from both the Main and Sub receivers are combined, and the resulting monaural
audio takes advantage of the combined aperture of the two speakers. For most operation, this configuration results
in beautiful audio reproduction, and is to be preferred. If you wish to leave the speaker setup as is, you may skip the
remainder of this section.
Speaker Selection Switch Configuration
1. Set the front panel’s [ POWER
] switch to the off (“ O
”)
position to turn the radio off.
2. Turn the FPS-9000H ’s POWER switch off (“
O
”),
and unlplug the DC cable from the rear-panel [DC
IN] jack.
3. Remove the eight screws from the left and right faces
of the outer case, then remove the three remaining
screws that are affixing the top case, and remove the
top case from the transceiver.
4. Refer to the illustration, and change the positin of the
speaker selection switch (the default setting is “COM”
which combines the audio; “SEP” separates the Main
(VFO-A) and Sub (VFO-B) receiver audio into the
Left and Right speakers).
5. Replace the three screws on the top case, then replace
the eight screws previously removed from the left and
right sides of the transceiver.
6. Speaker re-configuration is now complete. You may
now plug in the DC cable, and turn the FPS-9000H
and front panel [ POWER
] switches back on (in that
order), to resume operation.
Q Q
Q Q Q
UICK UICK UICK UICK UICK
P P
P P P
OINT OINT OINT OINT OINT
High-Quality Internal Speaker Details!
Two large-aperature, high quality speakers are incorporated into the FT
DX
9000MP , for outstanding reproduction
of the incoming audio signals. Sporting a combined aperture of 7” (184 mm), the twin 3-5/8” (92 mm) speakers are
designed to enhance your operating experience with their rich tonal quality and ultra-low distortion characteristics.
Speaker Select Switch
(Inside the Transceiver)
CCCCC
ONVENIENT ONVENIENT
ONVENIENT ONVENIENT
ONVENIENT
F F F F F
EA EA
EA EA
EATURES TURES
TURES TURES
TURES
AF AMP
EXT SPKR “A” Jack
EXT SPKR “B” Jack
Internal Speaker “A”
Internal Speaker “B”
BUFFER AMP
BUFFER AMP
COM
COMBINE
SEP
SEPARATE
MAIN BAND
VFO-A
( )
MAIN BAND
VFO-A
( )
SUB BAND
VFO-B ( )
SUB BAND
VFO-B
( )
Menu Selection 082
SPEAKER OUT
Speaker
Select Switch
AF AMP
COM
Main (VFO-A) and Sub (VFO-B) audio will be mixed in
the two internal speakers.
Main (VFO-A) audio will be heard from internal speaker
“
A .” For listening to audio from the Sub (VFO-B) receiver,
connect an external speaker to rear-panel terminal “ B .”
SEP
Main (VFO-A) and Sub (VFO-B) audio will be mixed but
heard only from the “
A ” internal speaker.
Main (VFO-A) audio will be heard from internal speaker
“
A ,” and Sub (VFO-B) audio will be heard from internal
speaker “ B .”
M
ENU
S
ELECTION
085
SPEAKER OUT
S
PEAKER
S
ELECT
S
WITCH
With respect to the switch on the Speaker Unit, the left position is
[
SEP
]
and the right position is
[
COM
]
.
COMBINE
SEPARATE