Yaesu FT DX 9000MP CONTEST - DATA MANAGEMENT OPERATION, Руководство по эксплуатации

Страница: 27 / 180

Page 25 FT
DX
9000MP O
PERATION
M
ANUAL
TX Indicator/Switch
When this button is pushed, the indicator will glow
Red, and the transmitter will be engaged on the same
frequency and mode as ws set up for the Main band
(VFO-A) (subject to any Clarifier offset, of course).
A
DVICE
:
If this indicator is not illuminated, it means that the
Sub (VFO-B) TX indicator has been selected (it will
be glowing Red). In this case, transmission will be
effected on the frequency and mode programmed for
the Sub (VFO-B) band.
Main Tuning Dial Knob
This large knob adjusts the operating frequency of the
Main band (VFO-A) or a recalled memory. Clock-
wise rotation of this knob increases the frequency.
Default tuning increments are 10 Hz (100 Hz in AM
and FM modes); when the [
FAST
] switch (#
be-
low) is pressed, the tuning steps increase. The avail-
able steps are:
Operating Mode 1 Step* 1Dial Rotation
LSB/USB/CW/RTTY/PKT(LSB) 10 Hz (100 Hz) 10 kHz (100 kHz)
AM/FM/PKT(FM) 100 Hz (1 kHz) 100 kHz (1 MHz)
*Numbers in parentheses indicate steps when the [ FAST
] switch is On.
A
DVICE
:
The tuning steps for the [
Main Tuning Dial
] knob
(described in this section) are set, at the factory, to 10
Hz per step. Via Menu item “
TUNING 139 DIAL
STEP ,” however, you may change this setting from
10 Hz to 5 Hz or 1 Hz instead. When press the [ FAST
]
button, the tuning step change to 100 Hz.
FAST Switch
Pressing this button will increase or decrease the tun-
ing rate of the [
MAIN Tuning Dial
] knob (#
above)
by a factor of ten, as mentioned in the previous section.
When this function is activated, the LED inside the
button will glow red.
LOCK Switch
This button toggles locking of the main tuning knob,
to prevent accidental frequency changes. When the
button is active, the [
MAIN Tuning Dial
] knob (#
,
described previously) can still be turned, but the fre-
quency will not change, and the LED inside the but-
ton will glow green.
NAR (Narrow) Switch
In the SSB/CW mode, this button is used to set the
bandwidth of the DSP IF filters to a user-programmed
bandwidth (default values are SSB: 1.8 kHz, CW/
RTTY/PSK: 300 Hz, AM: 6 kHz). When [
NAR
] has
been engaged, the [ WIDTH
] knob (#
, described
later) will be disabled.
In the AM mode, this button is used to toggle the
receiver’s bandwidth between wide (9 kHz) and nar-
row (6 kHz).
In the FM mode on the 28 MHz and 50 MHz bands,
this button is used to toggle the FM deviation/band-
width between wide (± 5.0 kHz Dev./25.0 kHz BW)
and narrow (± 2.5 kHz Dev./12.5 kHz BW).
Pressing the [
A
] or [
B
] button (located above the
MODE selection buttons) will select either the Main
band (VFO-A) or Sub band (VFO-B) for individual
bandwidth setting.
A
DVICE
:
When [ NAR
] has been engaged, the [
WIDTH
] knob
will be disabled, although IF Shift still works normally.
SPLIT Switch
Pressing this button to activates split frequency opera-
tion between the Main band (VFO-A), used for trans-
mission and Sub band (VFO-B), used for reception.
The same name LED located at the right of the main
tuning knob glows orange while this function is active.
If you press and hold in the [
SPLIT
] switch for two
seconds, the “Quick Split” feature will be engaged,
whereby the Sub band (VFO-B) VFO will automati-
cally be set to a frequency 5 kHz higher than the Main
band (VFO-A) frequency, and the transceiver will be
placed in the Split mode. Likewise, you may engage
an instant quick split by pressing and holding in the
[
SPLIT
] switch for two seconds; Quick Split will be
activated, and the transmit frequency will be set 5 kHz
higher than the current receiver frequency.
TXW “TX Watch” Switch
Pressing this key lets you monitor the transmit fre-
quency when split frequency operation is engaged.
When receiving on the transmit frequency, the LED
indicator will glow green. Release the key to return to
normal operation.
C.S Switch
Press this button momentarily to recall a favorite Menu
Selection directly.
To program a Menu selection as the short-cut, press
the [
MNU
] key (#
, described later) to enter the
Menu, then select the item you want to set as the short-
cut. Now press and hold in the [
C/S
] key for two sec-
onds; this will lock in the selected Menu item as the
short-cut.
The LED to the left of this switch will flash red when
the transmit and receive serial CAT command signals
are being exchanged.
A
DVICE
You may disable the LED function (flashes in con-
junction with CAT command) via Menu item “
GEN-
ERAL 037 CAT DATA INDICATOR .” See page 150
for details.
FFFFF
RRRRRONT ONT
ONT ONT ONT
P P P P P
ANEL ANEL
ANEL ANEL ANEL
C C C C C
ONTR ONTR
ONTR ONTR ONTROLS
OLS
OLS OLS OLS