background image

Lazerpoint

TM

 RF TX-9

Transmitter  

Installation Instructions

Ver.  1.01                 

General Description

Camden Lazerpoint™ Radio Controls comprise the following models:
CM-TX-9 Wall switch ready transmitter
CM-RX-91 Basic Receiver
CM-RX-92 Full function (dual relay) Receiver.

TX-9 transmitters utilize readily available AAA batteries, and 
special circuitry to assure long life.

A proprietary piezo sounder is used to annunciate low battery, 
battery level, and “stuck switch” conditions.

These instructions cover the TX-9 transmitter.

Mounting

The TX-9 is designed to mount behind a switch in a wall-box, post, 
or other suitable enclosure. Double sided tape is used to attach 
the circuit board and battery holder securely to the enclosure. 
Even though the circuit board is conformal coated, care should 
be taken to ensure the transmitter does not get wet.

Wiring

Refer to the TX-9 Installation Drawing (see reverse side) for the 
following connections:
Connect the transmitter wires to the activating switch (N.O. 
momentary dry contacts). Insert 2 fresh AAA alkaline batteries 
(provided) into the battery holder (observe proper polarity).  Press 
the switch and observe the red LED to ensure proper transmission.
Test the transmitter by pressing and holding the switch for 5 
seconds. The piezo speaker should sound 5 beeps, meaning the 
batteries are at full capacity.  This is the Battery Gauge™ feature.
If the piezo beeps only 1 - 3 times, you should change the batteries 
for fresh (new) ones.
Now press and hold the switch for 15 seconds. The piezo should 
now make a distinctive hi-low sound. This signal will sound for 
6 seconds, then turn off for a minute, then sound again. 
This is the “stuck switch indicator” feature.

Learning the Transmitter(s) to the Receiver

To learn the transmitter into the receiver, press the PB1  
(or PB2) button on the Receiver using a small blunt object such 

as a small blade screwdriver or similar.  Within 10 seconds, 
press the switch connected to the TX-9 transmitter.  The Green 
LED Array will flash once to confirm enrolment.  Repeat with 
any additional transmitters.  Pressing the learned transmitter 
again will signal the receiver that you are finished programming 
and LED’s 1 & 2 will flash, in an alternating sequence. 

 

Pressing the transmitter a third time will activate the relay and 
corresponding LED, and also the device connected to the relay 
contacts.

If you wait longer than the 10 second period, the receiver will 
time out of Learn Mode and revert back to standby. The LED 
will then flash to indicate the number of transmitters learned 
into the receiver.

Technical Data

Model 

  TX-9 

Transmitter

Frequency:                   Operates in the 902 – 928 MHz  
   ISM 

Band

Codes   

 

1 million (20 bit) codes

Size 

 

 

2 ¼” L x 5/8” W x 3/8” H

Mounting 

 

Double sided foam tape

Switch Connection 

2 x 10” leads with ¼” quick  

   disconnect 

terminations

Built-in Piezo sounder 

Used for Low Battery status,  

 

 

 

Battery Gauge™, and Stuck  

   Switch 

indicator.

Power   

 

2 x AAA alkaline batteries

Battery life 

 

Minimum 500,000 operations

Range   

 

Over 500 ft (open area)

Temperature rating 

-40

 o 

to 185

F (-40

 o 

to +85

 o 

C)

Warranty

Camden Door Controls guarantees the Lazerpoint™ RF 
(TX-9, RX-91,or RX-92 models) to be free from manufacturing 
defects for 3 years from date of sale. If during the first 3 
years a Lazerpoint RF component fails to perform correctly, 
it may be returned to our factory where it will be repaired or 
replaced (at our discretion) without charge.  Except as stated 
herein, Camden extends no warranties expressed or implied 
regarding function, performance or service.

NOTE: Batteries are exempt from this warranty!

Page 1 of 3

Reviews: