Xylem Flygt 5520 Скачать руководство пользователя страница 3

Страница: 3 / 54

Table of Contents

Introduction and Safety.........................................................................................................................3

Introduction..........................................................................................................................................3
Safety.....................................................................................................................................................3

Transportation and Storage..................................................................................................................7

Inspect the delivery.............................................................................................................................7

Inspect the package.........................................................................................................................7
Inspect the unit..................................................................................................................................7

Transportation guidelines..................................................................................................................7

Precautions........................................................................................................................................7
Position and fastening......................................................................................................................7
Lifting..................................................................................................................................................7

Temperature ranges for transportation, handling and storage....................................................8

Handling at freezing temperature..................................................................................................8
Unit in as-delivered condition.........................................................................................................8
Lifting the unit out of liquid.............................................................................................................8

Storage guidelines..............................................................................................................................9

Storage location................................................................................................................................9
Long-term storage............................................................................................................................9

Product Description.............................................................................................................................10

Pump design......................................................................................................................................10
Parts....................................................................................................................................................11
Monitoring equipment.....................................................................................................................12

Optional sensors.............................................................................................................................12

The data plate....................................................................................................................................13
Product denomination......................................................................................................................14

Installation.............................................................................................................................................15

Install the pump.................................................................................................................................15

Make the electrical connections......................................................................................................19

Check the impeller rotation.............................................................................................................30

Operation..............................................................................................................................................32

Precautions.........................................................................................................................................32
Distance to wet areas........................................................................................................................32

Table of Contents

Flygt 5520 Installation, Operation, and Maintenance Manual

Содержание Flygt 5520























































Результаты поиска

Содержание Flygt 5520

Отзывы:

Похожие инструкции для Flygt 5520

Бренды по названию

Популярные бренды

Xylem Flygt 5520, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Flygt 5520

Отзывы:

Похожие инструкции для Flygt 5520

Бренды по названию

Популярные бренды