Xylem Flygt 5520 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 54

background image

1. Empty all pumped liquid, if applicable.
2. Check all liquids used for lubrication or cooling, both oil and water-glycol mixtures, for

the presence of water. Change if needed.

Storage guidelines

Storage location

The product must be stored in a covered and dry location free from heat, dirt, and
vibrations.

NOTICE:

• Protect the product against humidity, heat sources, and mechanical damage.
• Do not place heavy weights on the packed product.

Long-term storage

If the unit is stored more than 6 months, the following apply:

• Before operating the unit after storage, it must be inspected with special attention to

the seals and the cable entry.

• The impeller/propeller must be rotated every other month to prevent the seals from

sticking together.

Transportation and Storage

Flygt 5520 Installation, Operation, and Maintenance Manual

9

«
...
9
10
11
12
13
...
»

Содержание Flygt 5520























































Отзывы:

Нет отзывов

Похожие инструкции для Flygt 5520

Бренд: A.O. Smith Страницы: 2

Бренд: DAB Страницы: 13

Бренд: SAER Elettropompe Страницы: 16

Бренд: Quincy Compressor Страницы: 122

Бренд: York Страницы: 84

Бренд: P.Lindberg Страницы: 54

Бренд: Fairland Pioneer Страницы: 36

Бренд: SAER Elettropompe Страницы: 44

DynaDrive DD60-10

Бренд: Davey Страницы: 32

Бренд: Daikin Страницы: 44

Бренд: A.O. Smith Страницы: 18

Бренд: Daikin Страницы: 300

Бренд: AL-KO Страницы: 120

Бренд: JW Страницы: 28

Бренд: Wayne Страницы: 24

Бренд: Rain Bird Страницы: 1

Бренд: Olympus Страницы: 36

Бренд: Daikin Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды