Xylem Flygt 5520 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 54

background image

Installation

Install the pump

WARNING:

• Electrical shock hazard. Check that the cable and cable entry have not been damaged

during transport before installing the pump.

• Note that special rules apply to installation in explosive atmospheres.
• Make sure that the unit cannot roll or fall over and injure people or damage property.
• Do not install CSA-approved products in locations that are classified as hazardous in the

national electric code, ANSI/NFPA 70-2005.

• Do not install the starter equipment in an explosive zone unless it is explosion-proof

rated.

NOTICE:

• Do not run the pump dry.
• Never force piping to make a connection with a pump.
• Always remove all debris and waste material from the sump, inlet piping, and

discharge connection, before you install the pump.

These requirements apply:

• Use the pump dimensional drawing in order to ensure proper installation.
• Provide a suitable barrier around the work area, for example, a guard rail.
• Check the explosion risk before you weld or use electric hand tools.
• Always check the impeller rotation before lowering the pump into the pumped liquid.

Authority regulation

Vent the tank of a sewage machine station in accordance with local plumbing codes.

Fasteners

WARNING:

• Only use fasteners of the proper size and material.
• Replace all corroded fasteners.
• Make sure that all fasteners are properly tightened and that there are no missing

fasteners.

Installation

Flygt 5520 Installation, Operation, and Maintenance Manual

15

«
...
15
16
17
18
19
...
»

Содержание Flygt 5520























































Отзывы:

Нет отзывов

Похожие инструкции для Flygt 5520

Бренд: Quick Страницы: 16

Бренд: Jacuzzi Страницы: 8

Бренд: Qual Craft Страницы: 5

Бренд: Fedders Страницы: 4

Бренд: JABSCO Страницы: 4

Бренд: TapFlo Страницы: 13

Бренд: A.O. Smith Страницы: 2

Residential Gas Water Heaters

Бренд: A.O. Smith Страницы: 84

Бренд: Galletti Страницы: 60

Бренд: Wacker Neuson Страницы: 42

Бренд: T.I.P. Страницы: 134

Бренд: Calorex Страницы: 44

Бренд: Carrier Страницы: 36

Бренд: CASELLA CEL Страницы: 27

Бренд: VAC-CON Страницы: 16

Бренд: Bock Water heaters Страницы: 60

Бренд: Kohler Страницы: 24

Бренд: SKAMET Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды