Xylem Flygt 5520 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 54

background image

NOTICE:

• Thermal contacts are incorporated in the pump.
• Thermal contacts must never be exposed to voltages higher than 250 V, breaking

current maximum 4 A. It is recommended that they are connected to 24 V over
separate fuses to protect other automatic equipment.

1. If thermal contacts are included in the pump installation, connect the T1 and T2 control

conductors to the monitoring equipment.
Do not connect the T1 and T2 leads to thermal contacts if the temperature of the
pumped liquid is above 40°C (104°F).

NOTICE:

Ex-approved products must always have the thermal contacts connected irrespective
of the ambient temperature.

2. Connect the mains leads (L1, L2, L3, and earth [ground]) to the starter equipment.

For information about the phase sequence and the color codes of the leads, see

3. Check the functionality of the monitoring equipment:

a) Check that the signals and the tripping function work properly.
b) Check that the relays, lamps, fuses, and connections are intact.
Replace any defective equipment.

Cable charts

Description

This topic contains general connection information. It also provides cable charts that show
connection alternatives for use with different cables and power supply.

L2

L1

L2

L3

L3

L1

WS000509B

WS000509C

L2

L3

L1

L1

L3

L2

T1 T2

Figure 6: Phase sequence

Connection locations

The figures in this section illustrate how to interpret the connection strip symbols.

Installation

22

Flygt 5520 Installation, Operation, and Maintenance Manual

«
...
22
23
24
25
26
...
»

Содержание Flygt 5520























































Отзывы:

Нет отзывов

Похожие инструкции для Flygt 5520

Бренд: EasyPro Страницы: 4

Goulds Marlow Series

Бренд: Xylem Страницы: 8

Бренд: Xylem Страницы: 12

Бренд: QEP Страницы: 2

Бренд: EINHELL Страницы: 44

SUPER T T6A60S-4LE2X FT4 Series

Бренд: GORMAN-RUPP PUMPS Страницы: 48

POWERplus POWX1700

Бренд: VARO Страницы: 10

Бренд: Leader Pumps Страницы: 8

Бренд: Ocean Technologies Страницы: 2

FXV-1212C-32Q-M/Q

Бренд: BAC Страницы: 47

Vickers 25V Series

Бренд: Eaton Страницы: 11

GHS 1 1/2 GF 32

Бренд: GORMAN-RUPP PUMPS Страницы: 47

Бренд: DROPSA Страницы: 14

Бренд: GORMAN-RUPP PUMPS Страницы: 25

Бренд: Intex Страницы: 5

Бренд: Mex Страницы: 2

Бренд: Lochinvar Страницы: 1

Бренд: Eckerle Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды