Xylem Flygt 5520 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 54

background image

NOTICE:

Do NOT override the motor protection repeatedly if it has tripped. Doing so may result in
equipment damage.

Cause

Remedy

The impeller rotates in the wrong

direction.

• If it is a 3-phase pump, transpose two phase leads.
• If it is a 1-phase pump:

Contact the local Xylem service shop.

One or more of the valves are set in

the wrong positions.

• Reset the valves that are set in the wrong position.
• Replace the valves, if necessary.
• Check that all valves are correctly installed according to media flow.
• Check that all valves open correctly.

The impeller is difficult to rotate by

hand.

• Clean the impeller.
• Clean out the sump.
• Check that the impeller is properly trimmed.

The pipes are obstructed.

Clean out the pipes to ensure a free flow.

The pipes and joints leak.

Find the leaks and seal them.

There are signs of wear on the

impeller, pump, and casing.

Replace the worn parts.

The liquid level is too low.

• Check that the level sensor is set correctly.
• Depending on the installation type, add a means for priming the pump,

such as a foot valve.

If the problem persists, refer to the Flygt Service Guide on the web or contact the local
Xylem service shop. Always state the serial number of your pump when you contact Xylem,
see

Product Description

Troubleshooting

48

Flygt 5520 Installation, Operation, and Maintenance Manual

«
...
48
49
50
51
52
...
»

Содержание Flygt 5520























































Отзывы:

Нет отзывов

Похожие инструкции для Flygt 5520

Бренд: Barnes Страницы: 12

Бренд: salmson Страницы: 16

Бренд: vacuubrand Страницы: 76

Бренд: Valeo Страницы: 88

Бренд: Valdemar Energy Страницы: 61

DURA-Power DRE-52

Бренд: A.O. Smith Страницы: 26

DURA-Power DRE-52

Бренд: A.O. Smith Страницы: 20

Elmo Rietschle V-VC 40

Бренд: Gardner Denver Страницы: 32

Бренд: Enviroheat Страницы: 20

Бренд: Enviroheat Страницы: 29

Бренд: IDEAL Страницы: 30

Alwayzaire P3062

Бренд: Bestway Страницы: 2

Green Line D90 GL

Бренд: dosatron Страницы: 2

Бренд: Laars Страницы: 64

Бренд: Sulzer Страницы: 4

Бренд: Annovi Reverberi Страницы: 4

Бренд: Gardenline Страницы: 2

Бренд: Bock Water heaters Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды