Xylem Flygt 5520 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 54

background image

Cause

Remedy

• The impeller
• The sump in order to prevent the impeller from clogging again.

If the problem persists, refer to the Flygt Service Guide on the web or contact the local
Xylem service shop. Always state the serial number of your pump when you contact Xylem,
see

Product Description

The pump does not stop when a level sensor is used

WARNING:

Always disconnect and lock out power before servicing to prevent unexpected startup.
Failure to do so could result in death or serious injury.

Cause

Remedy

The pump is unable to empty the

sump to the stop level.

Check that:
• There are no leaks from the piping and/or discharge connection.
• The impeller is not clogged.
• The non-return valve(s) are functioning properly.
• The pump has adequate capacity. For information:

Contact the local Xylem service shop.

There is a malfunction in the level-

sensing equipment.

• Clean the level regulators.
• Check the functioning of the level regulators.
• Check the contactor and the control circuit.
• Replace all defective items.

The stop level is set too low.

Raise the stop level.

If the problem persists, refer to the Flygt Service Guide on the web or contact the local
Xylem service shop. Always state the serial number of your pump when you contact Xylem,
see

Product Description

The pump starts-stops-starts in rapid sequence

Cause

Remedy

The pump starts due to back-flow

which fills the sump to the start

level again.

Check that:
• The distance between the start and stop levels is sufficient.
• The non-return valve(s) work(s) properly.
• The length of the discharge pipe between the pump and the first non-

return valve is sufficiently short.

The self-holding function of the

contactor malfunctions.

Check:
• The contactor connections.
• The voltage in the control circuit in relation to the rated voltages on the

coil.

• The functioning of the stop-level regulator.
• Whether the voltage drop in the line at the starting surge causes the

contactor's self-holding malfunction.

Troubleshooting

46

Flygt 5520 Installation, Operation, and Maintenance Manual

«
...
46
47
48
49
50
...
»

Содержание Flygt 5520























































Отзывы:

Нет отзывов

Похожие инструкции для Flygt 5520

Бренд: Haier Страницы: 2

Бренд: EAS Electric Страницы: 165

Бренд: Gardena Страницы: 16

Бренд: Gardena Страницы: 9

Бренд: Gardena Страницы: 11

13000 aquasensor

Бренд: Gardena Страницы: 14

Бренд: CLIVET Страницы: 7

POWERplus POWX1700

Бренд: VARO Страницы: 10

Бренд: Leader Pumps Страницы: 8

Бренд: Ocean Technologies Страницы: 2

FXV-1212C-32Q-M/Q

Бренд: BAC Страницы: 47

Бренд: Metabo Страницы: 77

Бренд: RainScapes Страницы: 2

Бренд: Redring Страницы: 4

PULSAR Shadow Series

Бренд: Pulsafeeder Страницы: 46

Бренд: Watts Страницы: 24

Бренд: Wilden Страницы: 39

Бренд: Tallas Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды