Xylem Flygt 5520 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 54

background image

Product Description

Pump design

The pump is submersible, and driven by an electric motor.

Intended use

The product is intended for moving wastewater, sludge, raw and clean water. Always
follow the limits that are given in

Application limits

(page 49). If there is a question

regarding the intended use of the equipment, please contact an Xylem representative
before proceeding.

WARNING:

In explosive or flammable environments, only use Ex- or MSHA-approved pumps.

NOTICE:

Do NOT use the pump in highly corrosive liquids.

Spare parts

• Modifications to the unit or installation should only be carried out after consulting with

Xylem.

• Original spare parts and accessories that are authorized by Xylem are essential for

compliance. The use of other parts can invalidate any claims for warranty or
compensation. For more information contact your Xylem representative.

Pressure class

MT

Medium head

Product Description

10

Flygt 5520 Installation, Operation, and Maintenance Manual

«
...
10
11
12
13
14
...
»

Содержание Flygt 5520























































Отзывы:

Нет отзывов

Похожие инструкции для Flygt 5520

Бренд: Gardena Страницы: 13

Бренд: WarmFlow Страницы: 89

Бренд: Graco Страницы: 56

Streamline 270MDV

Бренд: Solahart Страницы: 56

Бренд: Zehnder Pumpen Страницы: 32

Summit Pumper Vacuum

Бренд: Alto Страницы: 6

Бренд: Edwards Страницы: 60

Бренд: EBARA Страницы: 28

Cylinder Passport

Бренд: WarmFlow Страницы: 16

Бренд: Elite Страницы: 9

Бренд: DROPSA Страницы: 14

THBF701 Master Series

Бренд: bluefin Страницы: 17

Бренд: Newton Страницы: 4

Бренд: Giant Страницы: 12

Бренд: T.I.P. Страницы: 108

Бренд: Little Giant Страницы: 24

Бренд: emaux Страницы: 21

Бренд: WaterFurnace Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды