Xylem Flygt 5520 Скачать руководство пользователя страница 51

Страница: 51 / 54

Technical Reference

Motor data

Feature

Description

Motor type

Frequency

50 or 60 Hz

Supply

3-phase

Starting method

• Direct on-line
• Star-delta

Maximum starts per

hour

30 evenly spaced starts per hour

Code compliance

IEC 60034-1

Rated output variation

±5%

Voltage variation without

overheating

±10%, provided that it does not run continuously at full load

Voltage imbalance

tolerance

Stator insulation class

H (180°C [360°F])

Application limits

Data

Description

Liquid temperature

40°C (104°F) maximum
The pump must work fully submerged under full load operation.
Warm-liquid version : 70°C (158°F) maximum. These versions have certain operating

limitations which are stated on the plate on the pump.

Liquid density

Contact the local Xylem representative

pH of the pumped media

(liquid)

5.5–14

Depth of immersion

20 m (65 ft) maximum

Other

For the specific weight, current, voltage, power ratings, and speed of the pump, see

the data plate of the pump.

Technical Reference

Flygt 5520 Installation, Operation, and Maintenance Manual

Содержание Flygt 5520























































Результаты поиска

Содержание Flygt 5520

Отзывы:

Бренды по названию

Популярные бренды

Xylem Flygt 5520, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Flygt 5520

Отзывы:

Бренды по названию

Популярные бренды