Xylem Flygt 5520 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 54

background image

• The minimum bending radius must not be below the accepted value.
• If using a cable which has been used before, a short piece must be peeled off when

refitting it so that the cable entry seal sleeve does not close around the cable at the
same point again. If the outer sheath of the cable is damaged, then replace the cable.
Contact an Xylem service shop.

• The voltage drop in long cables must be taken into account. The drive unit’s rated

voltage is the voltage measured at the cable connection point in the pump.

• The screened cable must be used according to the European CE requirements if a

Variable Frequency Drive (VFD) is used. For more information, contact your Xylem
representative (VFD-supplier).

Earthing (Grounding)

Electrical Hazard:

• You must earth (ground) all electrical equipment. This applies to the pump equipment,

the driver, and any monitoring equipment. Test the earth (ground) lead to verify that it is
connected correctly.

• If the motor cable is jerked loose by mistake, the earth (ground) conductor should be the

last conductor to come loose from its terminal. Make sure that the earth (ground)
conductor is longer than the phase conductors. This applies to both ends of the motor
cable.

• Risk of electrical shock or burn. You must connect an additional earth- (ground-) fault

protection device to the earthed (grounded) connectors if persons are likely to come
into physical contact with the pump or pumped liquids.

Connect the motor cable to the pump

CAUTION:

Leakage into the electrical parts can cause damaged equipment or a blown fuse. Keep the
end of the motor cable above the liquid level.

Installation

20

Flygt 5520 Installation, Operation, and Maintenance Manual

«
...
20
21
22
23
24
...
»

Содержание Flygt 5520























































Отзывы:

Нет отзывов

Похожие инструкции для Flygt 5520

Altherma EKHWE150A3V3

Бренд: Daikin Страницы: 10

Бренд: EBARA Страницы: 48

Бренд: GEA Страницы: 66

Бренд: Atlantic Страницы: 20

Бренд: SAER Elettropompe Страницы: 20

Бренд: WAGNER Страницы: 120

Бренд: Graco Страницы: 32

Бренд: Malibu Boats Страницы: 2

Бренд: emaux Страницы: 21

Бренд: BSC Страницы: 28

Бренд: Samoa Страницы: 38

Бренд: Binks Страницы: 36

Бренд: Crivit Страницы: 26

Бренд: Xylem Страницы: 2

NOVA UP MAE Series

Бренд: DAB Страницы: 176

Бренд: Larzep Страницы: 6

Бренд: Kärcher Страницы: 74

Бренд: Mitsubishi Electric Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды