Xylem Flygt 5520 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 54

background image

Make the electrical connections

General precautions

Electrical Hazard:

• A certified electrician must supervise all electrical work. Comply with all local codes and

regulations.

• Before starting work on the unit, make sure that the unit and the control panel are

isolated from the power supply and cannot be energized. This applies to the control
circuit as well.

• Leakage into the electrical parts can cause damaged equipment or a blown fuse. Keep

the end of the motor cable above the liquid level.

• Make sure that all unused conductors are insulated.
• There is a risk of electrical shock or explosion if the electrical connections are not

correctly carried out or if there is fault or damage on the product.

WARNING:

Do not install the starter equipment in an explosive zone unless it is explosion-proof rated.

CAUTION:

If the pump is equipped with automatic level control and/or internal contactor, there is a
risk of sudden restart.

Requirements

These general requirements apply for electrical installation:

• The supply authority must be notified before installing the pump if it will be connected

to the public mains. When the pump is connected to the public power supply, it may
cause flickering of incandescent lamps when started.

• The mains voltage and frequency must agree with the specifications on the data plate.

If the pump can be connected to different voltages, then the connected voltage is
specified by a yellow sticker close to the cable entry.

• The fuses and circuit breakers must have the proper rating, and the pump overload

protection (motor protection breaker) must be connected and set to the rated current
according to the data plate and if applicable the cable chart. The starting current in
direct-on-line start can be up to six times higher than the rated current.

• The fuse rating and the cables must be in accordance with the local rules and

regulations.

• If intermittent operation is prescribed, then the pump must be provided with

monitoring equipment supporting such operation.

• If stated on the data plate, then the motor is convertible between different voltages.
• The thermal contacts/thermistors must be in use.

Cables

These are the requirements to follow when you install cables:

• The cables must be in good condition, not have any sharp bends, and not be pinched.
• The sheathing must not be damaged and must not have indentations or be embossed

(with markings, etc.) at the cable entry.

• The cable entry seal sleeve and washers must conform to the outside diameter of the

cable.

Installation

Flygt 5520 Installation, Operation, and Maintenance Manual

19

«
...
19
20
21
22
23
...
»

Содержание Flygt 5520























































Отзывы:

Нет отзывов

Похожие инструкции для Flygt 5520

Бренд: Quooker Страницы: 12

Бренд: YUKEN KOGYO Страницы: 82

Бренд: Navien Страницы: 83

Бренд: Aspen Pumps Страницы: 13

AQUA PLUS 200 LT

Бренд: Ferroli Страницы: 96

Бренд: Modine Manufacturing Страницы: 28

Бренд: Edwards Страницы: 56

Бренд: Greencut Страницы: 54

Бренд: SOLARFOCUS Страницы: 52

Бренд: Elkay Страницы: 2

Бренд: Laars Страницы: 64

LARIUS VEGA 5:1

Бренд: Samoa Страницы: 28

Бренд: Seisco Страницы: 20

Copper Cricket 1B

Бренд: Sage Advance Corp Страницы: 67

Бренд: Davey Страницы: 8

SiFire EN 100/200-205-45 E

Бренд: Wilo Страницы: 108

AlwaysFresh HFC-1000

Бренд: Waterline Technology Страницы: 6

Бренд: Grundfos Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды