Xtore NASolution NP1040 Скачать руководство пользователя страница 15

Страница: 15 / 186

NFP Storage Manager 1.1 User’s Manual

Chapter 2. Setting Up NP1040 NAS Server

Chapter 2

Setting up NP1040 NAS Server

After connecting your

NP1040

NAS server to a power source and

LAN, power it up and use

NFP Setup Assistant

to locate the server

and configure its IP address.

TIP

Setup procedure for the

NP1040

NAS server:

1. Make sure all internal components and hard disk drives (HDD)

are properly installed. (Please refer to the Hardware Installation
Guide for detailed instructions)

2. Connect

NP1040

to LAN and power source, and then turn it

on.

3. Run

NFP Setup Assistant

from any Windows terminal on the

LAN to locate and configure

NP1040

server’s IP address. Once

this is done a browser window will be opened automatically,
and you are connected to

NFP Storage Manager

NP1040

Server (See details below).

4. Use

NFP Storage Manager

’s

Quick Configuration

to configure

the basic options of the server (see Chapter 3).

5. Use

NFP Storage Manager

to configure the details of the

server, such as system configuration, user privileges, and
network and hard disks management (see Chapter 4).

Before you start

Please install HDD into

NP1040

NAS server.

When purchasing diskless model that supports DOC/DOM,
please install at least one HDD before turning on the server.

Содержание NASolution NP1040



























































































































































































Результаты поиска

Содержание NASolution NP1040

Отзывы:

Похожие инструкции для NASolution NP1040

Бренды по названию

Популярные бренды

Xtore NASolution NP1040, Руководство пользователя

Результаты поиска

Содержание NASolution NP1040

Отзывы:

Похожие инструкции для NASolution NP1040

Бренды по названию

Популярные бренды