Xtore NASolution NP1040 Скачать руководство пользователя страница 110

Страница: 110 / 186

NFP Storage Manager 1.1 User’s Manual

NFP

Backup Utility: Backing up and restoring data on the server

105

Click

Apply

. The system starts the back up process. Click

Report

to review the backed up data after the back up process

is finished.

Note:

Make sure the hard disk configuration or volume status has not

been changed when restoring data back onto

NP1040

NAS

server; i.e. the hard disks are configured as Non-RAID when

backing up the data, but when data is being restored, the

configuration has already been changed to RAID 0. This would

lead to incorrect restoring, therefore we strongly advise system

administrator not to restore data between different hard disk

configurations.

When restoring data back onto

NP1040

NAS server, please

verify there is enough storage space on the server for data

restoring; otherwise the restoring process will fail.

When backing up/restoring data, many temporary files will be

generated in the first volume of the system, therefore the

backing up/restoring cannot be performed if free storage space

in the first volume is less than 10MB.

When the system fails to backup/restore data on

NP1040

NAS server,

system administrator will receive an e-mail with an error code notifying

the data backup/restore failure. The administrator can also go to

system log

tab of

NFP Storage Manager

and search for the error

code in the log file. Below follows an explanation of the e-mail error

codes:

Содержание NASolution NP1040



























































































































































































Результаты поиска

Содержание NASolution NP1040

Отзывы:

Похожие инструкции для NASolution NP1040

Бренды по названию

Популярные бренды

Xtore NASolution NP1040, Руководство пользователя

Результаты поиска

Содержание NASolution NP1040

Отзывы:

Похожие инструкции для NASolution NP1040

Бренды по названию

Популярные бренды