Xstream X-HW13008GENNG, Руководство по эксплуатации

Страница: 25 / 40

25
WARNING
THE TRIGGER GUN SHOULD ALWAYS BE LOCKED IN THE OFF
POSITION WHEN NOT IN USE!
NEVER LOOK DIRECTLY AT THE NOZZLE UNLESS IT IS DISCON-
NECTED FROM THE TRIGGER GUN/DUAL LANCE ASSEMBLY!
CONNECTION OF Q.C. NOZZlES QUICK-CONNECT (Q.C.)
12
12 Operator's Manual
INSTALLATION & PREPARATION
WATER SUPPLY:
1. Select a water supply hose which is a quality grade of garden hose measuring
at least 3/4" ID and no longer than 50 feet.
2 Check the water inlet strainer to ensure it is clean and free of any obstructions.
As a strainer becomes obstructed, it restricts proper flow of water to the
pump. This can result in cavitations which will prematurely cause failure
of pump packings.
a. Using a screwdriver, remove the screen from the water inlet.
b. Clean or replace if necessary.
3. Connect the hoses.
a. Connect one end of the water supply hose to the water inlet of the unit.
b. Connect the other end of the hose to your pressurized water supply.
NOTE 1: Do not use a non-pressurized water supply (i.e. from a pond or
well) with this unit.
NOTE 2: When connecting the water inlet to the water supply mains, local
regulations of your water company must be observed. In some
areas, the unit must not be connected directly to the public drinking
water supply. This is to ensure there is no feedback of detergents
into the water supply. (Direct connection is permitted if a backflow
preventer is installed. Check with local authorities for approval.)
NOTE 3: If there is a high mineral content in your water, it is highly
recommended that a water softener and an additional water strainer
be added to the water inlet to help prevent the possibility
of excessive scale buildup inside the heat exchanger coil. Clean
both strainers before starting your pressure washer.
NOZZLE REVIEW:
Various nozzles may be quick-connected into the end of the wand to change the
spray pattern or use the detergent feature. When using Quick Connects (Q.C.),
be certain the connection is securely locked. If not, the high pressure water
may shoot the nozzle from the wand, causing severe injury or serious damage.
To determine spray fan, refer to the actual number stamped on the nozzle. The
first two digits indicate the spray fan in degrees, i.e.; 00=0”, 15=15°, 40=40°.
1. The 0° nozzle (RED): This is a blasting nozzle. It delivers a very concentrated
stream of water. Be cautious when using the straight narrow stream. It is
not recommended for use on painted or wood surfaces, or items attached
with adhesive backings. Uses: Removing weeds from sidewalk cracks,
stubborn stains from concrete, masonry, aluminum and steel, caked mud
from equipment, and cleaning lawn mower undersides.
2. The 15° nozzle (YELLOW) : This is a chiseling nozzle. The spray should
be directed at a 45° angle to the surface and used like a scraper to remove
paint, grease and dirt. Uses: Surface preparation (removing mildew stains
and paint chips).
3.
The 40° nozzle (WHITE)
:
This is a wash nozzle. This wide spray pattern disperses the water pressure
over a large area and is recommended for moderate washing. Uses: Washing
aluminum siding, cleaning windows, washing vehicles, spraying sidewalks,
driveways, and patios.
NOZZLE CONNECTION:
1. Be certain the trigger gun is locked in the “OFF” position. See WARNING , left.
2. The nozzle assembly should be disconnected from the gun/wand assembly
at this by retracting the locking ring on the quick-connect fitting to remove
the nozzle.
WARNING
RISK OF INJECTION CAUSING
SEVERE INJURY!
NEVER LOOK DIRECTLY AT THE
NOZZLE ORIFICE UNLESS IT
IS DISCONNECTED FROM THE
GUN/WAND ASSEMBLY!
CONNECTION OF Q.C. NOZZLES
QUICK-CONNECT FITTING
WARNING
RISK OF SEVERE INJURY!
THE TRIGGER GUN SHOULD
ALWAYS BE LOCKED IN THE OFF
POSITION WHEN NOT IN USE!
QUICK-CONNECT (Q.C.)
0°
15°
40°
Operator's Manual 9
preparation
QuicK-connect noZZles :
Various nozzles may be quick connected into the end of the adjustable pressure
dual lance to change the spray pattern or use the detergent feature. When
using Quick- connects (Q.C.), be certain the connection is securely locked.
(See illustration #). If not, the high pressure water may shoot the nozzle
from the lance, causing severe injury or serious damage. To determine
spray fan, (see illustration #2) refer to the actual number stamped on the
nozzle. The first two digits indicate the spray fan in degrees, i.e., 00=0°,
15=15°, 25=25°, 40=40°.
. the 0° nozzle (red) : This is a blasting nozzle. It delivers a very concentrated
stream of water. Be cautious when using the straight narrow stream. It is
not recommended for use on painted or wood surfaces or items attached
with adhesive backings. Uses: Removing weeds from sidewalk cracks,
stubborn stains from concrete, masonry, aluminum and steel, caked mud
from equipment, and cleaning lawn mower undersides.
2. the 15° nozzle (yellow) : This is a chiseling nozzle. The spray should
be directed at a 45° angle to the surface and used like a scraper to
remove paint, grease and dirt. Uses: Surface preparation (removing
mildew stains and paint chips).
3. the 25° nozzle (green) :
a. This is a flushing nozzle. This pattern is best suited for flushing
dirt, mud, and grime. Uses: Wet sweeping leaves from walk,
curbs and driveways, cleaning stable floors, washing swimmin
pool bottoms, degreasing engines.
b. On units with steam option, this nozzle is used for 250°F Wet
Steam operation. This nozzle is sized for operation with the
unloader and steam valve (where applicable) to provide high
pressure wet steam. Replacement of this nozzle with an improp-
erly sized nozzle may cause operational problems with the
machine.
4. the 40° nozzle (wHite) : This is a wash nozzle. This wide spray pattern
disperses the water pressure over a large area and is recommended
for moderate washing. Uses: Washing down aluminum siding, cleaning
windows, washing vehicles, spraying sidewalks, driveways, and
patios.
illustration #11
QuicK connect
illustration #12
Q.c. noZZles
. Ensure the trigger gun is locked in the OFF position. (See illustration
#3)
2. The quick-connect nozzle should be disconnected from the adjustable
pressure dual lance at this time. As shown in illustration #4, retract the
locking ring on the quick-connect fitting to remove the nozzle.
illustration #14
noZZle connection
noZZle connection:
WARNING
risK of inJection causing
seVere inJury!
tHe trigger gun sHould
always be locKed in tHe off
position wHen not in use!
neVer looK directly at
tHe noZZle unless it is
disconnected from tHe
trigger gun/dual lance
assembly!
illustration #13
gun locK
preparation
NOZZlE CONNECTION
1. Ensure the trigger gun is locked in the OFF position.
2. The quick-connect nozzle should be disconnected from the adjustable
pressure dual lance at this time. Retract the locking ring on the quick-
connect fitting to remove the nozzle.
Operator's Manual 9
preparation
QuicK-connect noZZles :
Various nozzles may be quick connected into the end of the adjustable pressure
dual lance to change the spray pattern or use the detergent feature. When
using Quick- connects (Q.C.), be certain the connection is securely locked.
(See illustration #). If not, the high pressure water may shoot the nozzle
from the lance, causing severe injury or serious damage. To determine
spray fan, (see illustration #2) refer to the actual number stamped on the
nozzle. The first two digits indicate the spray fan in degrees, i.e., 00=0°,
15=15°, 25=25°, 40=40°.
. the 0° nozzle (red) : This is a blasting nozzle. It delivers a very concentrated
stream of water. Be cautious when using the straight narrow stream. It is
not recommended for use on painted or wood surfaces or items attached
with adhesive backings. Uses: Removing weeds from sidewalk cracks,
stubborn stains from concrete, masonry, aluminum and steel, caked mud
from equipment, and cleaning lawn mower undersides.
2. the 15° nozzle (yellow) : This is a chiseling nozzle. The spray should
be directed at a 45° angle to the surface and used like a scraper to
remove paint, grease and dirt. Uses: Surface preparation (removing
mildew stains and paint chips).
3. the 25° nozzle (green) :
a. This is a flushing nozzle. This pattern is best suited for flushing
dirt, mud, and grime. Uses: Wet sweeping leaves from walk,
curbs and driveways, cleaning stable floors, washing swimmin
pool bottoms, degreasing engines.
b. On units with steam option, this nozzle is used for 250°F Wet
Steam operation. This nozzle is sized for operation with the
unloader and steam valve (where applicable) to provide high
pressure wet steam. Replacement of this nozzle with an improp-
erly sized nozzle may cause operational problems with the
machine.
4. the 40° nozzle (wHite) : This is a wash nozzle. This wide spray pattern
disperses the water pressure over a large area and is recommended
for moderate washing. Uses: Washing down aluminum siding, cleaning
windows, washing vehicles, spraying sidewalks, driveways, and
patios.
illustration #11
QuicK connect
illustration #12
Q.c. noZZles
. Ensure the trigger gun is locked in the OFF position. (See illustration
#3)
2. The quick-connect nozzle should be disconnected from the adjustable
pressure dual lance at this time. As shown in illustration #4, retract the
locking ring on the quick-connect fitting to remove the nozzle.
illustration #14
noZZle connection
noZZle connection:
WARNING
risK of inJection causing
seVere inJury!
tHe trigger gun sHould
always be locKed in tHe off
position wHen not in use!
neVer looK directly at
tHe noZZle unless it is
disconnected from tHe
trigger gun/dual lance
assembly!
illustration #13
gun locK
Operator's Manual 9
preparation
QuicK-connect noZZles :
Various nozzles may be quick connected into the end of the adjustable pressure
dual lance to change the spray pattern or use the detergent feature. When
using Quick- connects (Q.C.), be certain the connection is securely locked.
(See illustration #). If not, the high pressure water may shoot the nozzle
from the lance, causing severe injury or serious damage. To determine
spray fan, (see illustration #2) refer to the actual number stamped on the
nozzle. The first two digits indicate the spray fan in degrees, i.e., 00=0°,
15=15°, 25=25°, 40=40°.
.
the 0° nozzle (red)
: This is a blasting nozzle. It delivers a very concentrated
stream of water. Be cautious when using the straight narrow stream. It is
not recommended for use on painted or wood surfaces or items attached
with adhesive backings. Uses: Removing weeds from sidewalk cracks,
stubborn stains from concrete, masonry, aluminum and steel, caked mud
from equipment, and cleaning lawn mower undersides.
2. the 15° nozzle (yellow) : This is a chiseling nozzle. The spray should
be directed at a 45° angle to the surface and used like a scraper to
remove paint, grease and dirt. Uses: Surface preparation (removing
mildew stains and paint chips).
3.
the 25° nozzle (green)
:
a. This is a flushing nozzle. This pattern is best suited for flushing
dirt, mud, and grime. Uses: Wet sweeping leaves from walk,
curbs and driveways, cleaning stable floors, washing swimmin
pool bottoms, degreasing engines.
b. On units with steam option, this nozzle is used for 250°F Wet
Steam operation. This nozzle is sized for operation with the
unloader and steam valve (where applicable) to provide high
pressure wet steam. Replacement of this nozzle with an improp-
erly sized nozzle may cause operational problems with the
machine.
4. the 40° nozzle (wHite) : This is a wash nozzle. This wide spray pattern
disperses the water pressure over a large area and is recommended
for moderate washing. Uses: Washing down aluminum siding, cleaning
windows, washing vehicles, spraying sidewalks, driveways, and
patios.
illustration #11
QuicK connect
illustration #12
Q.c. noZZles
. Ensure the trigger gun is locked in the OFF position. (See illustration
#3)
2. The quick-connect nozzle should be disconnected from the adjustable
pressure dual lance at this time. As shown in illustration #4, retract the
locking ring on the quick-connect fitting to remove the nozzle.
illustration #14
noZZle connection
noZZle connection:
WARNING
risK of inJection causing
seVere inJury!
tHe trigger gun sHould
always be locKed in tHe off
position wHen not in use!
neVer looK directly at
tHe noZZle unless it is
disconnected from tHe
trigger gun/dual lance
assembly!
illustration #13
gun locK
gun lock
nozzle connection