Xilinx CAN FD v2.0 Скачать руководство пользователя страница 76

Страница: 76 / 98

CAN FD v2.0

PG223 December 5, 2018

www.xilinx.com

Chapter 3:

Designing with the Core

2. The CAN FD changes the buffer status to Full when the message is received without

errors and is timestamped. In case of errors (for example, CRC error), the buffer status

remains Active.

3. If enabled through IERBF and IER, the

RXRBF

bit is set in the ISR register (when the core

changes the RCS buffer status to Full) and interrupt is generated.

Notes

The CAN FD accesses the RX block RAM message element space of a buffer based on the

buffer status.

a. Active: Read access for ID and Mask. Write access for the received message. Read

and Write access for the timestamp.

b. Full: Read access for ID and Mask to find overflow condition.

The host should respect access rules to avoid memory collisions. For example,

a. If the buffer status is Active, do not access the corresponding block RAM space.
b. If the buffer status is Full, do not change the respective ID and Mask.

IMPORTANT:

Because ID and Mask registers are in the block RAM, asserting a software reset or system

reset does not clear these register contents. Host has to properly initialize them before use.

Notes on the ID Match Process

1. It is expected that the AXI4-Lite/APB clock frequency is sufficiently fast that the match

process finishes before the frame reception is completed on the CAN bus.

2. If the core is not able to complete the match process before the EOF sixth bit, it sets the

RX MNF

bit in the ISR register.

3. The RX Mailbox control logic in the Object layer waits for the Transfer layer to signal

RXOK

(EOF sixth bit) before setting the corresponding RCSx(i) bit to indicate that the RX

Buffer is full.

4. It is possible for the CAN bus to encounter an error after the Data field of the current

frame (the sixth bit of the EOF field). In this situation, the Mailbox control logic does not

set the RCSx(i) bit to indicate that the RX Buffer is full. The RX block RAM matched

element might show a partial or full data update.

5. The ID received with the message is written into the ID field of the Mailbox buffer.

Example 1:

Host programmed ID & Mask:

ID reg

: 0x1234_5678

Mask reg : 0xFFFF_FF00

Incoming IDs 0x1234_56xx will match this mailbox buffer.

Send Feedback

Содержание CAN FD v2.0



































































































Результаты поиска

Содержание CAN FD v2.0

Отзывы:

Похожие инструкции для CAN FD v2.0

Бренды по названию

Популярные бренды

Xilinx CAN FD v2.0, Руководство по эксплуатации продукта

Результаты поиска

Содержание CAN FD v2.0

Отзывы:

Похожие инструкции для CAN FD v2.0

Бренды по названию

Популярные бренды