Xilinx CAN FD v2.0 Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 98

background image

CAN FD v2.0

73

PG223 December 5, 2018

Chapter 3:

Designing with the Core

5. After reading the message, write the FSR register by setting the respective IRI bit to 1.

This enables the core to increment the respective Read Index field by +1 and updates

the corresponding Fill Level in the FSR register. If Fill level is 0, setting IRI bit has no

effect.

6. Repeat steps 3 through 5 until all messages are read from either RX FIFO-0 or RX

FIFO-01.

RX – Core Actions

1. When a message is successfully received, the core writes the timestamp and matched

filtered index field of the received message element.

2. The CAN FD increments the Fill Level of its respective RX FIFO in the FSR register by 1

after every successful receive (without error and message passes filtering scheme).

3. The Fill Level is also updated by the core after the Host writes the IRI bit of respective RX

FIFO in the FSR register.

Filtering

Each acceptance filter pair has an Acceptance Filter Mask register and an Acceptance Filter

ID register. Each filter pair a has corresponding

UAF

bit to control enable/disable.

Filtering when RX FIFO-1 is absent or disabled

Filtering is performed in the following sequence:

1. The incoming Identifier is masked with the bits in the Acceptance Filter Mask register.
2. The Filter ID register is also masked with the bits in the Acceptance Filter Mask register.
3. Both resulting values are compared.
4. If both these values are equal, then the message is stored in RX FIFO-0.
5. Filtering is processed by each of the defined filters. If the incoming identifier passes

through any filter, the message is stored in RX FIFO-0.

Note:

RX FIFO-1 can be disabled (that is, stop routing messages to RX FIFO-1) by programming

RXFP as 'd31 (in RX FIFO Watermark register). See Register description for more detail.

Filtering when RX FIFO-1 is enabled

In this case, the

RXFP

field (in the RX FIFO Watermark register) along with the Filter

(Control) register determines whether received messages are stored in RX FIFO-0 or RX

FIFO-1. In this case, the

RXFP

field must be less than 'd31.

1. The incoming Identifier is masked with the bits in the Acceptance Filter Mask register.
2. The Filter ID register is also masked with the bits in the Acceptance Filter Mask register.

«
...
71
72
73
74
75
...
»

Содержание CAN FD v2.0



































































































Отзывы:

Нет отзывов

Похожие инструкции для CAN FD v2.0

Professional Series

Бренд: PACOM Страницы: 15

Бренд: Lauterbach Страницы: 61

Бренд: CAME Страницы: 19

Бренд: Yaesu Страницы: 2

Бренд: TFortis Страницы: 86

DM/IP601-CPCI-100BT

Бренд: Dialogic Страницы: 2

Бренд: Wintech Страницы: 21

Бренд: Marani Страницы: 39

LL140 RGB Series

Бренд: Corsair Страницы: 30

Бренд: Idis Страницы: 28

Бренд: Proxim Страницы: 45

Бренд: Paradyne Страницы: 10

CNPS7000B Series

Бренд: ZALMAN Страницы: 9

GigaSpire BLAST u6

Бренд: Calix Страницы: 9

Бренд: Tachosys Страницы: 15

Бренд: Jupiter Страницы: 2

WP-N6516-M2-16P

Бренд: Wisstar Страницы: 195

Бренд: Bosch Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды