Xilinx CAN FD v2.0 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 98

background image

CAN FD v2.0

56

PG223 December 5, 2018

Chapter 2:

Product Specification

RB*-DW1-15 Register (Address 0x210C, 0x2154…0x410C, 0x4154...)

Description similar to

Table 2-41, page 55

.

Note:

Only required DW locations needs to be read as per FDF and DLC field for a given message.

Acceptance Filters

There are 32 acceptance filters in RX Sequential/FIFO mode. Each acceptance filter has an

Acceptance Filter Mask register and an Acceptance Filter ID register (which is controlled by

the Acceptance Filter (Control) register bits described in

Table 2-27, page 37

Acceptance Filtering when RX FIFO-1 is absent or disabled

Acceptance filtering is performed in this sequence:

1. The incoming Identifier is masked with the bits in the Acceptance Filter Mask register.
2. The Acceptance Filter ID register is also masked with the bits in the Acceptance Filter

Mask register.

3. Both resulting values are compared.
4. If both these values are equal, the message is stored in RX FIFO-0.
5. Acceptance filtering is processed by each of the defined filters. If the incoming identifier

passes through any acceptance filter, the message is stored in RX FIFO-0.

Note:

RX FIFO-1 can be disabled (that is, stop routing messages to RX FIFO-1) by programming

RXFP

as 'd31 (in the RX FIFO Watermark register).

Acceptance Filtering when RX FIFO-1 is enabled

In this case, the

RXFP

field (in the RX FIFO Watermark register) along with the Acceptance

Filter (Control) register determines whether received messages are stored in RX FIFO-0 or

RX FIFO-1. In this case, the

RXFP

field should be less than 'd31. The incoming Identifier is

masked with the bits in the Acceptance Filter Mask register.

6. The Acceptance Filter ID register is also masked with the bits in the Acceptance Filter

Mask register.

7:0

Data bytes3 [7:0]

N/A

Data Byte 3.
Data byte that was received with CAN or CAN FD frame based on

DLC control field.

Notes:

1. Only required DW locations needs to be read as per FDF and DLC field for a given message.

Table 2-41:

RB DW0 Register

(Cont’d)

Bits

Name

Default

Value

Description

«
...
54
55
56
57
58
...
»

Содержание CAN FD v2.0



































































































Отзывы:

Нет отзывов

Похожие инструкции для CAN FD v2.0

Бренд: Vivotek Страницы: 136

Бренд: SMART Страницы: 15

Бренд: Hama Страницы: 8

Hollywood DV-Bridge

Бренд: Dazzle Страницы: 63

Бренд: Acces I/O products Страницы: 5

SINUS H PROFInet

Бренд: Enertronica Santerno Страницы: 34

Бренд: Advantech Страницы: 36

Бренд: Teletronics International Страницы: 57

Бренд: WABCO Страницы: 29

PowerBeam PBE-5AC-400-ISO

Бренд: Ubiquiti Страницы: 23

Бренд: Logicube Страницы: 56

PXI PXITM -1000

Бренд: National Instruments Страницы: 55

See3CAM 30 Z10X

Бренд: e-con Systems Страницы: 14

AirStation G54 WLA2-G54

Бренд: Buffalo Страницы: 8

Бренд: ACTi Страницы: 12

Бренд: Paradyne Страницы: 46

Бренд: National Instruments Страницы: 35

Бренд: Hitachi Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды