Xilinx CAN FD v2.0 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 98

background image

CAN FD v2.0

25

PG223 December 5, 2018

Chapter 2:

Product Specification

Interrupt Enable Register (Address 0x0020)

The Interrupt Enable register (IER) bits are used to enable interrupt generation when

respective event happens.

3

BSFRD

R

0

Bus-Off Recovery Done Interrupt.
• 1 = Indicates that the core recovered from Bus-Off state.

This bit can be cleared by writing to the respective bit in the ICR.

This bit is also cleared when a 0 is written to the CEN bit in the SRR.

2

PEE

R

0

Protocol Exception Event Interrupt.
• 1 = Indicates that the core (CAN FD receiver) has detected PEE event.

This bit can be cleared by writing to the respective bit in the ICR.

This bit is also cleared when a 0 is written to the CEN bit in the SRR.

1

TXOK(1)

R

0

Transmission Successful Interrupt.
• 1 = Indicates that a message was transmitted successfully.

This bit can be cleared by writing to the respective bit in the ICR. This

bit is also cleared when a 0 is written to the CEN bit in the SRR.

0

ARBLST

R

0

Arbitration Lost Interrupt.
• 1 = Indicates that arbitration was lost during message transmission.
This bit can be cleared by writing to the respective bit in the ICR. This

bit is also cleared when a 0 is written to the CEN bit in the SRR.

Notes:

1. In Loopback mode, both TXOK and RXOK bits are set. The RXOK bit is set before the TXOK bit.

Table 2-12:

Interrupt Status Register

(Cont’d)

Bits

Name

Access Default

Value

Description

Table 2-13:

Interrupt Enable Register

Bits

Name

Access

Default

Value

Description

31

ETXEWMFLL

R/W

0

TX Event FIFO Watermark Full Interrupt Enable.
• 1 = Enables interrupt generation if TXEWMFLL bit in the ISR is set.
• 0 = Disables interrupt generation if TXEWMFLL bit in the ISR is set.

30

ETXEOFLW

R/W

0

TX Event FIFO Overflow Interrupt Enable.
• 1 = Enables interrupt generation if TXEOFLW bit in the ISR is set.
• 0 = Disables interrupt generation if TXEOFLW bit in the ISR is set.

17

ERXMNF

R/W

0

RX Match Not Finished interrupt Enable.
• 1 = Enables interrupt generation if RXMNF bit in the ISR is set.
• 0 = Disables interrupt generation if RXMNF bit in the ISR is set.

«
...
23
24
25
26
27
...
»

Содержание CAN FD v2.0



































































































Отзывы:

Нет отзывов

Похожие инструкции для CAN FD v2.0

Бренд: Hal Communications Страницы: 25

Бренд: Paradyne Страницы: 20

Compshere 3000 Series

Бренд: Paradyne Страницы: 2

Бренд: X-Micro Страницы: 9

Бренд: X-Micro Страницы: 19

xCORE-200 Multi-channel Audio board

Бренд: XMOS Страницы: 112

Бренд: TFortis Страницы: 86

Бренд: Amplifier Tech Страницы: 36

HiGain HLU-231 List 8F

Бренд: ADC Страницы: 7

ST62GP-EMU2 HDS2 Series

Бренд: STMicroelectronics Страницы: 58

Бренд: H3C Страницы: 3

Бренд: IDT Страницы: 207

Бренд: Giacomini Страницы: 2

Бренд: Caton Страницы: 18

Бренд: XJTAG Страницы: 9

Бренд: Xilinx Страницы: 8

Бренд: Aaeon Страницы: 61

Бренд: Ubiquiti Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды