Xilinx CAN FD v2.0 Скачать руководство пользователя страница 67

Страница: 67 / 98

CAN FD v2.0

PG223 December 5, 2018

www.xilinx.com

Chapter 3:

Designing with the Core

Normal Mode

IMPORTANT:

The core can enter Normal mode only if Sleep, Loopback, and Snoop bits are 0 in the MSR

register.

In Normal mode, the core participates in bus communication by transmitting and receiving

messages.

Note:

In Normal mode, core does not store its own transmitted messages.

(Internal) Loopback Mode

IMPORTANT:

This mode is used for diagnostic purposes.

In Loopback mode, the core receives any messages that it transmits by an internal loopback

to the RX line and acknowledges them. Received messages are stored in receive buffers

based on ID match result. The core stores its own transmitted message (based on ID match

result) in mailbox buffers or sequential/FIFO buffers in Loopback mode.

It does not participate in normal bus communication and does not receive any messages

transmitted by other CAN nodes (the external TX line is ignored). It drives a recessive

bitstream on the CAN bus (external TX line).

Sleep Mode

The core enters Sleep mode from Configuration or Normal mode when the

SLEEP

bit is 1

in the MSR register, the CAN bus is idle, and there are no pending transmission requests.

The core enters Configuration mode when any configuration condition is satisfied. The core

enters Normal mode (clearing the

SLEEP

request bit in the MSR register and also clearing

the corresponding status bit) under the following (wake-up) conditions:

• Whenever the

SLEEP

bit is set to 0.

• Whenever the

SLEEP

bit is 1, and bus activity is detected.

• Whenever there is a new message for transmission.

Interrupts are generated when the core enters Sleep mode or wakes up from Sleep mode.

Send Feedback

Содержание CAN FD v2.0



































































































Результаты поиска

Содержание CAN FD v2.0

Отзывы:

Xilinx CAN FD v2.0, Руководство по эксплуатации продукта, Страница: 67 / 98

Результаты поиска

Содержание CAN FD v2.0

Отзывы: