Xerox Phaser 3310 Скачать руководство пользователя

Страница: 64 / 200

RINT

EDIA

Printing on Transparencies

Guidelines

• Only use transparencies recommended for use in laser printers.

• Do not load more than 20 transparencies into the Multi-Purpose Tray at a time.

• Make sure that the transparencies are not wrinkled or curled, and that they do not have

any torn edge.

• Hold the transparencies by the edges and avoid touching the print side. Oils from your

fingers that are deposited on the transparency can cause print quality problems.

• Be careful not to scratch or leave fingerprints on the print side.

Open the Multi-Purpose Tray and pull
the extender out of its full-length
position.

Load transparencies

with print side

, and

the top with the adhesive

strip entering the printer first

Adjust the guide to fit the width of the
transparencies.

When you print on transparencies,
configure the paper source, type and
size in the software application. For
details, see

page 5.3

Notes:

• To prevent transparencies from sticking

together, remove them from the output
tray as they are printed.

• Place transparencies on a flat surface

after removing them from the printer.

Содержание Phaser 3310









































































































































































































Результаты поиска

Содержание Phaser 3310

Отзывы:

Похожие инструкции для Phaser 3310

Бренды по названию

Популярные бренды

Xerox Phaser 3310, Руководство пользователя

Результаты поиска

Содержание Phaser 3310

Отзывы:

Похожие инструкции для Phaser 3310

Бренды по названию

Популярные бренды