Xerox D95 Скачать руководство пользователя страница 180 | Manualshive

Страница: 180 / 460

Xerox D95 Скачать руководство пользователя страница 180

Cause and Remedy

Fault code

Cause: A hard disk error occurred during image processing.
Remedy: The hard disk might be defective. When replacing a hard disk, contact
the Customer Support Center.

016-777

Cause: Conversion processing of scanned image was interrupted because of
insufficient disk space.
Remedy: Remove unnecessary data from the hard disk to increase free disk space.

016-778

Cause: An error occurred during scanned image conversion processing.
Remedy: Retry scanning.

016-779

Cause: A hard disk error occurred during scanned image conversion processing.
Remedy: The hard disk might be defective. When replacing a hard disk, contact
the Customer Support Center.

016-780

Cause: When using the scan feature, hard disk capacity is insufficient for writing
to a file.
Remedy: Either remove unnecessary data from the hard disk to increase free disk
space or initialize the hard disk.

016-786

Cause: Failed to load a file from the Web browser.
Remedy: Perform the following actions, and try again.
Reload the browser page
Restart the browser
Power-cycle the machine

016-788

Cause: Specified job history could not be acquired when printing Job Counter
Report
Remedy: Specified job history does not exist.

016-792

Cause: An illegal print parameter is included.
Remedy: Confirm the print data and option and specify the print data again.

016-799

Cause: During an inspection or maintenance request a transmission error occurred
and our Customer Support Center could not be contacted.
Remedy: Check that the phone lines are connected and try sending an inspection
or maintenance request again after a short time. If the error persists, contact the
Customer Support Center.

021-750
021-751
021-770
021-771
021-772

User Guide

15-22

Problem solving

«
...
178
179
180
181
182
...
»

Содержание D95













































































































































































































































































































































































































































































Отзывы:

Нет отзывов