Xerox 5400N - Phaser B/W Laser Printer Скачать руководство пользователя страница 94

Страница: 94 / 503

Phaser 5400 Laser Printer Service Guide

RAP 12 Error Code

E2-12: Tray 2 Jam

Open Tray 2

Error Code E2-13: Tray 3 Jam

Open Tray 3

A paper jam has occurred in the 2000-Sheet Feeder.

Table 32

Error Code E2-1: Paper Jam / Misfeed 2000-Sheet Feeder

Troubleshooting Procedure

Step Actions and Questions

Yes

PROCEDURE

1. Open the 2000-Sheet Feeder Upper Rear Cover

Assembly.

2. Remove the Jammed paper.

3. Run a test print.

Does the error message still appear?

Go to
Step 2.

Problem
solved.

PAPER INSPECTION

1. Pull out the 2000-Sheet Feeder Tray Assembly.

2. Check the paper condition and size.

Is the paper dry, in good condition and is the size

within specifications?

Go to
Step 3.

Replace with
fresh paper
of the proper
size from an
unopened
ream.

FEED MOTOR ASSEMBLY

1. Switch printer power OFF.

2. Remove the 2000-Sheet Feeder Right Side Cover

[RRP 12-5].

3. Open the Upper Rear Cover.

4. Manually rotate the top gear clockwise.

5. Inspect the rotation of the 2000-Sheet Feeder Motor

Assembly.

Does the Feed Motor Assembly rotate smoothly?

Go to
Step 4.

Replace the
2000-Sheet
Feeder Feed
Motor
Assembly
[RRP 12.16,

page 368

] or

gears.

REPLACE FEED ROLLER [

RRP 12.14,

page 366

]

Run Test prints.

Does the Error Code still appear?

Go to
Step 5.

Problem
solved.

TOP GEAR ROTATION

Manually rotate the top gear counterclockwise.

Does the 2000-Sheet Feeder Assembly rotate

smoothly and feed a sheet of paper from the

Feeder Tray Assembly?

Go to
Step 6.

Replace the
Feeder
Assembly
[PL 12.3,

page 422

], if

it does not
rotate
smoothly.

DRIVE ASSEMBLY GEARS

1. Remove the 2000-Sheet Feeder Tray Assembly

[RRP 12.7,

page 359

2. Rotate the gears of the Drive Assembly.

Do the gears of the Drive Assembly rotate

smoothly?

Go to
Step 7.

Replace the
Drive
Assembly
[RRP 12.13,

page 365

Содержание 5400N - Phaser B/W Laser Printer
























































































































































































































































































































































































































































































































Результаты поиска

Содержание 5400N - Phaser B/W Laser Printer

Отзывы:

Бренды по названию

Популярные бренды

Xerox 5400N - Phaser B/W Laser Printer, Справочное руководство по обслуживанию

Результаты поиска

Содержание 5400N - Phaser B/W Laser Printer

Отзывы:

Бренды по названию

Популярные бренды