Xerox 5400N - Phaser B/W Laser Printer Скачать руководство пользователя страница 157

Страница: 157 / 503

128

Phaser 5400 Laser Printer Service Guide

RAP 47 Main Motor Assembly

Table 75

Main Motor Assembly Troubleshooting Procedure

Step Actions and Questions

Yes

PROCEDURE

1. Open the Top Cover.

2. Remove the Print Cartridge.

3. Cheat the Top Cover Interlock.

4. Enter Diagnostics mode.

5. From the Main Menu, select Component Test / Main

Motor / press [4] to start test, [0] to stop.

Does the Main Motor rotate?

Problem
solved.

Go to
Step 2.

LVPS VOLTAGES

1. Switch print power OFF.

2. Remove the Lower Rear Cover [RRP 1.7,

page 256

3. Switch printer power ON.

4. Measure the voltages listed in the table [see Table 76

below] on the LVPS.

Are all voltages correct?

Go to
Step 7.

Go to
Step 3.

Are the voltages on pins 1 and 2 correct?

Go to
Step 4.

Replace the
LVPS
[RRP 8.6,

page 312

Is the voltage on pin 6 correct?

Go to
Step 5.

Replace the
Print Engine
Controller
Board
[RRP 8.5,

page 310

Is the voltage on pin 5 correct

Replace the
LVPS
[RRP 8.6,

page 312

Go to
Step 6.

“NO” FROM STEP 5 ABOVE

Check the voltage between P/J161-11 and frame
ground.

Does the voltage on P/J161-11 measure

+3.3 VDC?

Replace the
Print Engine
Controller
Board
[RRP 8.5,

page 310

Replace the
LVPS
[RRP 8.6,

page 312

“YES” FROM STEP 2 ABOVE

1. With the Top Cover Interlock still cheated, enter

Diagnostics mode.

2. From the Main Menu, select Component Test / Main

Motor.

3. Measure the voltage between P/J164-6 and frame

ground. Note this voltage, then continue with

sub-step 4.

4. Press [4] to start test, [0] to stop.

5. Measure (again) the voltage between P/J164-6 and

frame ground.

Does the voltage drop from +4.7 VDC (measured

in sub-step 3) to 0 VDC (measured in

sub-step 5)?

Go to
Step 9.

Go to
Step 8.

Содержание 5400N - Phaser B/W Laser Printer
























































































































































































































































































































































































































































































































Результаты поиска

Содержание 5400N - Phaser B/W Laser Printer

Отзывы:

Бренды по названию

Популярные бренды

Xerox 5400N - Phaser B/W Laser Printer, Справочное руководство по обслуживанию

Результаты поиска

Содержание 5400N - Phaser B/W Laser Printer

Отзывы:

Бренды по названию

Популярные бренды