Xerox 5400N - Phaser B/W Laser Printer Скачать руководство пользователя страница 235

Страница: 235 / 503

206

Phaser 5400 Laser Printer Service Guide

PAPER TRANSPORT ASSEMBLY INSPECTION

Inspect the Paper Transport Assembly for wear,
obstructions or contamination.

Is the Paper Transport Assembly free of wear,

obstructions and contamination?

Go to
Step 34

Clean, repair
or replace
the Paper
Transport
Assembly
[RRP 4.1,

page 283

Does the skewed image occur on printed from

the MBF Tray?

Go to
Step 14.

Go to
Step 18.

MBF FEED ROLLERS INSPECTION

Inspect the MBF Feed Rollers for contamination and/or
wear.

Are the MBF Feed Rollers free of contamination

and wear?

Go to
Step 15.

Replace the
MBF Feed
Rollers
[RRP 2.2,

page 261

MBF RETARD PAD INSPECTION

Inspect the MBF Retard Pad for wear, damage or
contamination.

Is the MBF Pad free of wear, damage or

contamination?

Go to
Step 16.

Clean or
replace the
MBF Pad
[RRP 2-5].

MBF CHUTE INSPECTION

Inspect the MBF Chute for obstructions and
contamination.

Is the MBF Chute free of obstructions and

contamination?

Go to
Step 17.

Clean the
MBF Chute
as
necessary.

REGISTRATION SENSOR INSPECTION

1. Inspect the Registration Sensor obstructions or

contamination.

2. Inspect the Registration Sensor Actuator for freedom

of operation, damage, obstructions and

contamination.

Is the Registration Sensor (and Actuator) free of

obstructions and contamination and does the

Registration Sensor Actuator move freely?

Go to
Step 34.

Clean or
replace the
Registration
Sensor or
Actuator as
necessary
[RRP 4.2,

page 285

RRP 4.4,

page 287

Does the skewed image occur on prints fed from

Tray 1?

Go to
Step 19.

Go to
Step 24.

TRAY 1 FEED ROLLERS INSPECTION

Inspect the Tray 1 Feed Rollers for wear or
contamination.

Are the Tray 1 Feed Rollers free of wear and

contamination?

Go to
Step 20.

Clean or
replace the
Tray 1 Feed
Rollers as
necessary
[RRP 2.10,

page 271

Table 113 Skewed Image Troubleshooting Procedure (cont'd.)

Step Actions and Questions

Yes

Содержание 5400N - Phaser B/W Laser Printer
























































































































































































































































































































































































































































































































Результаты поиска

Содержание 5400N - Phaser B/W Laser Printer

Отзывы:

Бренды по названию

Популярные бренды

Xerox 5400N - Phaser B/W Laser Printer, Справочное руководство по обслуживанию

Результаты поиска

Содержание 5400N - Phaser B/W Laser Printer

Отзывы:

Бренды по названию

Популярные бренды