Xerox 5400N - Phaser B/W Laser Printer Скачать руководство пользователя страница 123

Страница: 123 / 503

Phaser 5400 Laser Printer Service Guide

RAP 29 Error Code PSE-1: Paper Size Jam

Open Rear Cover

There is a conflict between the size of paper the printer senses in the paper tray and/or
MBF and the size of paper that is actually loaded.

Table 49

Error Code PSE-1 Paper Size Jam

Troubleshooting Procedure

Step Actions and Questions

Yes

Does the problem appear when using Tray 1, 2 or

Go to
Step 3.

Go to
Step 2.

MBF PAPER SIZE VERIFICATION

1. Open the MBF and verify the size of paper currently in

the MBF Tray.

2. Enter User Menus, select Tray Menu / MBF Size / then

scroll through the MBF Size sub-menus to find the

default paper size.

Does the paper size displayed on the LCD match

the size actually in the MBF?

Go to
Step 9.

Enter User
Menu /
select MBF
Size / then
select the
size
matching the
paper in the
MBF Tray.

Is the paper size in the problem tray within

printer specifications?

Go to
Step 4.

Replace with
paper that
meets
specs.

INSPECTING GUIDES

Inspect the side guides and Paper Stack End Guide in
the problem Tray.

Are all guides properly set for the size of paper

installed?

Go to
Step 5.

Properly set
the guides.

SIZE CAM INSPECTION

Inspect the size cam on the left side of the paper tray.

Are the cams in good condition (not broken) and

rotate freely as the paper tray end guide is

moved?

Go to
Step 6.

Replace the
paper tray
[PL 2.1,

page 386

PL 2.2,

page 388

TRAY SIZE TEST

1. Enter Diagnostics mode.

2. From the Main Menu, select Component Test / Tray

(1, 2 or 3 - the problem tray) Size / press [4] to start,

[0] to stop.

Does the paper size displayed on the LCD match

the size of the paper actually loaded?

Replace the
Print Engine
Controller
Board
[RRP 8.5,

page 310

Go to
Step 7.

SENSOR INPUT TEST

1. While still in Diagnostics mode from Step 6 above,

select Component Test / Sensor Input Test / press [4]

start, [0] to stop.

2. One at a time, press and release each of the problem

tray size actuators.

Does the LCD counter increment each time you

press and release one of the actuators?

Go to
Step 8.

Go to
RAP 54,

page 142

Содержание 5400N - Phaser B/W Laser Printer
























































































































































































































































































































































































































































































































Результаты поиска

Содержание 5400N - Phaser B/W Laser Printer

Отзывы:

Бренды по названию

Популярные бренды

Xerox 5400N - Phaser B/W Laser Printer, Справочное руководство по обслуживанию

Результаты поиска

Содержание 5400N - Phaser B/W Laser Printer

Отзывы:

Бренды по названию

Популярные бренды