manualshive.com logo in svg

Xerox 5400N - Phaser B/W Laser Printer, Справочное руководство по обслуживанию

Поделиться
Скачать
Xerox 5400N - Phaser B/W Laser Printer Скачать руководство пользователя страница 393

364

Phaser 5400 Laser Printer Service Guide

RRP 12.12 Harness Assembly 

(See 

PL 12.2 2000-Sheet Feeder (2 of 4)

)

Removal

Warning: Switch off the power and disconnect the Power Cord.

1.

Remove the Printer / 500-Sheet Feeder (RRP 11.1 500-Sheet Feeder Removal).

2.

Remove the Left Side Cover (RRP 12.2 Left Side Cover).

3.

Remove the Lower Rear Cover (RRP 12.4 Lower Rear Cover).

4.

Disconnect P/J601 from the 2000-Sheet Feeder PWB.

5.

Release the harness from all cable clamps.

6.

Remove the two screws that secure the harness connector to the frame.

7.

Guide the harness through the holes in the frame as you remove it.

Replacement

Reinstall the components in the reverse order.

Figure 154 Harness Assembly

Содержание 5400N - Phaser B/W Laser Printer
























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды