manualshive.com logo in svg

Xerox 5400N - Phaser B/W Laser Printer, Справочное руководство по обслуживанию

Поделиться
Скачать
Xerox 5400N - Phaser B/W Laser Printer Скачать руководство пользователя страница 103

74

Phaser 5400 Laser Printer Service Guide

RAP 16 Error Code

 

E5:

Close Covers

The Top Cover or Rear Cover is open.

Table 36

Error Code E5: Close Covers Troubleshooting Procedure

Step Actions and Questions

Yes

No

1

OPEN CLOSE TOP COVER AND REAR DOOR

Open and close the Rear Cover and the Top Cover.

Is the error message still displayed?

Go to 
Step 2.

Problem 
solved.

2

REAR COVER

1. Open the Rear Cover.

2. Slowly close the Rear Cover checking to ensure the 

cover is actuating the Rear Cover Interlock Switch.

Does the Rear Cover actuate the Interlock 

Switch?

Go to 
Step 3.

Realign or 
replace the 
Rear Cover 
[RRP 1-9

, 

page 258

].

3

TOP COVER

1. Open the Top Cover.

2. Slowly close the Top Cover check to ensure the cover 

is actuating the Top Cover Interlock Switch.

Does the Top Cover actuate the Interlock 

Switch?

Go to 
Step 4.

Replace the 
Top Cover 
[RRP 1.3, 

page 252

].

4

REMOVE LOWER REAR COVER

1. Switch printer power OFF.

2. Remove the Lower Rear Cover [RRP 1.7, 

page 256

].

3. Switch printer power ON.

4. Measure the voltage between P/J162-1 and frame 

ground.

Does the voltage m24 VDC?

Go to 
Step 5.

Go to 
RAP 40, 

page 114

.

5

“YES” FROM STEP 4 ABOVE

Measure the voltage between P/J162-3 and frame 
ground.

Does the voltage m24 VDC?

Replace the 
Print Engine 
Controller 
Board 
[RRP 8.5, 

page 310

].

Go to 
Step 6.

6

“NO” FROM STEP 4 ABOVE

1. Switch printer power OFF.

2. Remove the Right Side Cover [RRP 1.2, 

page 251

].

3. Switch printer power ON.

4. Measure the voltage between the Top Cover Interlock 

Switch, both terminals, (P/J623) and frame ground.

Do both voltages m24 VDC?

Go to 
Step 7.

Check the 
wiring 
between the 
Rear Cover 
Interlock 
Switch. If the 
wiring is OK, 
replace the 
Top Cover 
Interlock 
Switch 
[RRP 7.4, 

page 302

].

Содержание 5400N - Phaser B/W Laser Printer
























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды