Xerox 5400N - Phaser B/W Laser Printer Скачать руководство пользователя страница 290 | Manualshive

Страница: 290 / 503

Xerox 5400N - Phaser B/W Laser Printer Скачать руководство пользователя страница 290

Phaser 5400 Laser Printer Service Guide

261

RRP 2.2 MBF Feed Rollers

PL 4.1 Multi-sheet Bypass Feeder (MBF) Assembly

Removal

Warning: Switch off the power and disconnect the Power Cord.

1.

Remove the MBF Assembly (RRP 2.1 Multi-sheet Bypass Feeder (MBF)
Assembly).

2.

For the Left Feed Roller, lift the locking tab on the Left MBF Roller Core and slide

the core to the left. Slide the MBF Feed Roller to the left and remove.

3.

For the Right Feed Roller, lift the locking tab on the Right MBF Roller Core and
slide the core to the right. Slide the MBF Feed Roller to the right and remove.

Replacement

Reinstall the components in the reverse order.

Note:

Arrows of the back side of the Feed Rollers indicate direction

of rotation.

Figure 48 MBF Feed Roller Assembly

«
...
288
289
290
291
292
...
»

Содержание 5400N - Phaser B/W Laser Printer
























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды