manualshive.com logo in svg

Xerox 5400N - Phaser B/W Laser Printer, Справочное руководство по обслуживанию

Поделиться
Скачать
Xerox 5400N - Phaser B/W Laser Printer Скачать руководство пользователя страница 252

Phaser 5400 Laser Printer Service Guide 

223

Recommended Corrective Action

For most of the blink code errors, the System Controller Board should be replaced. 
For Hard Disk and DIMM slot errors, the cause of the error could be either the 
System Controller Board or the plugged-in accessory. If the blink error points to a 

(HD or RAM) component that is not even installed, the System Controller is to blame. 
Otherwise, be prepared to replace either component (DIMM or HD and the System 
Controller).

Power On LED Sequence

The following LEDs on the System Controller Board aid in identifying faults during 

the Power On sequence. The LEDs provide status information in all powered ON 
operating modes.

Table 120 System Controller LEDs

LED

Location Color Description

Power - 
CR6

CR 6

Red

Indicates power to the controller. Should stay on when power is 
turned on.

Test - CR1 CR 1

Red

Indicates that a power on diagnostics failure has occurred when 
flashing.

Speed

CR 4

Red

ON: 10 Mbit Ethernet
OFF: 100 Mbit Ethernet

Link

CR 3

Green OFF: Indicates no Ethernet link found

ON: Indicates Ethernet link found

RXD

CR 2

Yellow OFF: Indicates no activity on Ethernet link

ON: Indicates activity on Ethernet link

Содержание 5400N - Phaser B/W Laser Printer
























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды