manualshive.com logo in svg

Xerox 5400N - Phaser B/W Laser Printer, Справочное руководство по обслуживанию

Поделиться
Скачать
Xerox 5400N - Phaser B/W Laser Printer Скачать руководство пользователя страница 65

36

Phaser 5400 Laser Printer Service Guide

Remove Output 
from Std. Bin

C5: Top Tray Full

Top Tray is declared full when 5 prints 
are delivered to the top tray after the 
Full Stack sensor is actuated.

Empty Top Tray.
Go to RAP 6, 

page 52

.

Remove Output 
from Stacker Bin

C5: HCS Tray Full

Five prints are delivered to the top tray 
after the HCS Full Stack sensor is 
actuated.

Empty HCS Tray.
Go to RAP 7, 

page 55

.

Disk Error
Format Disk

D-1

Hard Drive error was detected.

■

Power Off/On.

■

Format Hard Drive - 

See Reset Menu 

(RAP 68, 

page 172

).

■

Replace Hard Drive.

■

Replace System 

Controller Board 

(RRP 8.1, 

page 305

).

Init Failed
Disk Locked

D-2

Cannot format disk, disk locked via 
PJL or SNMP Command.

■

Customer Unlock 

Disk.

■

Replace Hard Disk.

Format Failed
Disk Locked

D-3

Cannot put disk in factory default 
attempt to initialize disk after it is 
locked.

■

Customer Unlock 

Disk.

■

Replace Hard Disk.

Memory Failure
Power Off/On

ESS-M

Controller memory has failed (32 MB 
on board).

■

Power Off/On

■

Remove Options

■

Replace System 

Controller PWB 

(RRP 8.1, 

page 305

).

NV Memory Fail
Power Off/On

ESS-N

Controller NVM Failure

■

Power Off/On

■

Replace System 

Controller PWB 

(RRP 8.1, 

page 305

).

Paper Jam
Open Top Cover
Open/Extend 
MBF
Remove PrintCart
Clear Paper Path

E1-1

E1: Reg. Jam

1. Registration Sensor did not 

deactuate within time after actuation 

of Registration sensor.

2. Registration sensor is actuated at 

power on.

3. Registration is actuated during 

warm up cycle or an erase cycle.

Open Top Cover, 
remove EP Cartridge. 
Open and Extend MBF 
assembly and remove 
any paper.
Go to RAP 9, 

page 60

.

Duplex Jam
Open Rear Cover
Clear Paper Path

E2-D

E2-2: Misfeed Jam

Registration Sensor did not actuate 
within time after the actuation of the 
Duplex Motor in reverse.

Open Rear Cover and 
remove any paper.
Go to RAP 13, 

page 67

.

Table 18

Error Code / Repair Analysis Procedure (cont'd.)

Displayed 

Error Message

Fault

History
Log

Diagnostic Message / 

Fault Description /
Comment

Action

Содержание 5400N - Phaser B/W Laser Printer
























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды