manualshive.com logo in svg

Xerox 3450B - Phaser B/W Laser Printer, Руководство по обслуживанию, Страница: 9 / 180

Поделиться
Скачать
Xerox 3450B - Phaser B/W Laser Printer Скачать руководство пользователя страница 9

viii

Phaser 3450 Laser Printer 

Servicing Electrical Components

Before starting any service procedure, switch off the printer power and unplug the 
power cord from the wall outlet. If you must service the printer with power applied, 
be aware of the potential for electrical shock.

Warning

Turning the power off by using the On/Off switch does not completely de-
energize the printer. You must also disconnect the printer power cord from the 
AC outlet. Position the power cord so that it is easily accessible during servicing. 

Warning

Do not touch any electrical component unless you are instructed to do so by a 
service procedure.

Servicing Mechanical Components

When servicing mechanical components within the printer, manually rotate drive 
assemblies, rollers, and gears.

Warning

Do not try to manually rotate or manually stop the drive assemblies while any 
printer motor is running.

Servicing Fuser Components

Warning

This printer uses heat to fuse the toner image to media. The Fuser Assembly is 
VERY HOT. Turn the printer power off and wait at least 5 minutes for the Fuser 
to cool before you attempt to service the Fuser Assembly or adjacent 
components. 

S7300-02

S7300-03

Содержание 3450B - Phaser B/W Laser Printer





















































































































































































Отзывы:

Нет отзывов