manualshive.com logo in svg

Xerox 3450B - Phaser B/W Laser Printer, Руководство по обслуживанию, Страница: 79 / 180

Поделиться
Скачать
Xerox 3450B - Phaser B/W Laser Printer Скачать руководство пользователя страница 79

4-12

Phaser 3450 Laser Printer Service Manual

Jam At Duplex (Duplex Jam 1)

Paper jams in the Exit Transport Assembly or before, or in the Duplex Feed Rollers.

Troubleshooting References

Procedure

Applicable Parts

Wiring and Plug/Jack Map References

Exit Sensor Actuator 

Exit Roller Assembly

Transport Roller Assembly

Main Board

Step

Action and Questions

Yes

No

1

Is the Exit Sensor Actuator damaged or binding? Repair or 

replace the 

actuator and/or 

sensor.

Go to Step 2.

2

Inspect the Exit Roller Assembly. Is it damaged 

or binding?

Replace the Exit 

Roller 

Assembly.

Go to Step 3.

3

Inspect the Duplexer. Is any paper wrapped 

around the Duplex Rollers?

Remove 

obstruction and 

clean rollers.

Go to Step 4.

4

Is the Transport Roller Assembly operational 

(rotates freely without binding)?

Go to Step 5.

Replace 

Transport 

Roller 

Assembly.

5

Use the embedded diagnostics to check the 

Fuser Exit Sensor. Is the sensor operational?

Replace Main 

Board.

Replace Exit 

Sensor.

s3450-167

Содержание 3450B - Phaser B/W Laser Printer





















































































































































































Отзывы:

Нет отзывов