Xerox 3450B - Phaser B/W Laser Printer Скачать руководство пользователя страница 77

Страница: 77 / 180

4-10

Phaser 3450 Laser Printer Service Manual

Jam At Top (Jam 1)

Paper jams in front of or just inside the Fuser Assembly.

Troubleshooting References

Procedure

Applicable Parts

Wiring and Plug/Jack Map References

Exit Sensor Actuator

Registration Sensor Actuator

Fuser Assembly

Power Supply Board

Step

Action and Questions

Yes

Is the Exit Sensor Actuator damaged or binding? Repair or

replace the

actuator and/or

sensor.

Go to Step 2.

Is the Registration Sensor Actuator damaged or

binding?

Repair or

replace the

actuator and/or

sensor.

Go to Step 3

Is paper wrapped around the Fuser rollers or

blocking Fuser exit?

Remove paper

and clean Fuser

rollers.

Go to Step 4.

Is Fuser operational, the Fuser Rollers turn

freely when the motor is on?

Go to Step 5.

Replace Fuser

Assembly.

Use the embedded diagnostics to check the

Fuser Exit Sensor. Is the sensor operational?

Replace Power

Supply Board.

Replace Fuser

Exit Sensor.

Содержание 3450B - Phaser B/W Laser Printer





















































































































































































Результаты поиска

Содержание 3450B - Phaser B/W Laser Printer

Отзывы:

Xerox 3450B - Phaser B/W Laser Printer, Руководство по обслуживанию, Страница: 77 / 180

Результаты поиска

Содержание 3450B - Phaser B/W Laser Printer

Отзывы: