manualshive.com logo in svg

Xerox 3450B - Phaser B/W Laser Printer, Руководство по обслуживанию, Страница: 55 / 180

Поделиться
Скачать
Xerox 3450B - Phaser B/W Laser Printer Скачать руководство пользователя страница 55

3-8

Phaser 3450 Laser Printer Service Manual

Service Diagnostics

The Phaser 3450 Laser Printer has built-in diagnostics to aid in troubleshooting 
problems with the printer. The Service Diagnostics Menu provides a means to test 
sensors, motors, switches, clutches, fans and solenoids. Diagnostics also contain 
built-in test prints, cleaning procedures, printer status and some NVRAM access.

Service diagnostics are to be executed through the front panel by a certified service 
technician only. The printer must be rebooted to enter Service Diagnostics:

Entering Service Diagnostics:

1.

Turn the printer power OFF.

2.

Hold down the OK button and turn the printer back ON.

3.

Continue to hold the button until the following mesage is displayed on the front 
panel: 

“Diagnostic Mode” / “Press Menu Key”

, and then release the OK 

button.

4.

Press the Menu button and use the Arrow buttons to scroll through the available 
functions (see the following Button Functions and Menu Map).

Содержание 3450B - Phaser B/W Laser Printer





















































































































































































Отзывы:

Нет отзывов