manualshive.com logo in svg

Xerox 3450B - Phaser B/W Laser Printer, Руководство по обслуживанию, Страница: 118 / 180

Поделиться
Скачать
Xerox 3450B - Phaser B/W Laser Printer Скачать руководство пользователя страница 118

Service Parts Disassembly

8-21

Replacement Notes

Note

A ground wire and a discharge capacitor are secured to the Main Drive 
Assembly by 2 of the mounting screws. Note the position for reassembly.

Note

Seat the right side of the Main Drive first, then work the left side into 
position while aligning the gears. Reattach the Cover Interconnect Board 
after the Main Drive is positioned.

Tray 2 Solenoid (PL 9.1.28)

1.

Remove the Main Drive Assembly (page 8-19).

2.

Disconnect CN 10 between the Tray 2 Solenoid and the Connector Board.

3.

Remove 2 screws that secure the Tray 2 Solenoid to the chassis, and remove the 
Tray 2 Solenoid.

Tray 2 No Paper Sensor (PL 9.3.44)

1.

Remove the left cover from the printer (page 8-8)

2.

Disconnect CN 2 (to Registration Sensor) from the sensor board.

3.

Disconnect CN 3 (to Print Cartridge Interconnect Board) from the sensor board.

4.

Remove 2 screws securing the Tray 2 No Paper Sensor to the printer chassis and 
remove the sensor.

1

s3450-026

Содержание 3450B - Phaser B/W Laser Printer





















































































































































































Отзывы:

Нет отзывов