Xerox 3450B - Phaser B/W Laser Printer Скачать руководство пользователя страница 72

Страница: 72 / 180

General Troubleshooting

4-5

Power Supply Troubleshooting

Troubleshooting References

Applicable Parts

Wiring and Plug/Jack Map References

Power Supply Board

AC Switch Harness Assembly

Procedure

Step

Action and Questions

Yes

Check the voltage at the AC wall outlet. Is

there approximately 110 VAC (or 220 VAC if

the printer is a 220 V model) at the AC wall

outlet?

Go to Step 2.

Notify the

customer of

improper AC

output from the

outlet.

Check the power cord for defects or a loose

connection.

Replace or

reseat the

power cord.

Go to Step 3.

Disconnect the Power Cord and turn the AC

switch ON.

Check the AC Switch Harness for continuity.

Replace the

Power Supply

Board.

Replace the AC

Switch Harness

Assembly.

Содержание 3450B - Phaser B/W Laser Printer





















































































































































































Результаты поиска

Содержание 3450B - Phaser B/W Laser Printer

Отзывы:

Xerox 3450B - Phaser B/W Laser Printer, Руководство по обслуживанию, Страница: 72 / 180

Результаты поиска

Содержание 3450B - Phaser B/W Laser Printer

Отзывы: