Xerox 3450B - Phaser B/W Laser Printer Скачать руководство пользователя страница 81

Страница: 81 / 180

4-14

Phaser 3450 Laser Printer Service Manual

CRUM Toner Error

Troubleshooting References

Procedure

Applicable Parts

Wiring and Plug/Jack Map References

Print Cartridge

Toner Sensor Harness

Print Cartridge Interconnect Board

Step

Action and Questions

Yes

Open the top cover and ensure that the Print

Cartridge is properly seated. Does the error

clear after reseating the cartridge?

Complete

Go to Step 2.

Reseat all harness connections to the Print

Cartridge Interconnect Board. Does the error

clear?

Complete

Go to Step 3.

Check continuity between the Print Cartridge

Interconnect Board and CN6 on the Main Board.

Does the harness show continuity?

Go to Step 4.

Replace

Harness.

Check Print Cartridge. Does the cartridge

contain toner and appear to be operating

properly?

Replace Print

Cartridge

Interconnect

Board.

Replace Print

Cartridge.

Содержание 3450B - Phaser B/W Laser Printer





















































































































































































Результаты поиска

Содержание 3450B - Phaser B/W Laser Printer

Отзывы:

Xerox 3450B - Phaser B/W Laser Printer, Руководство по обслуживанию, Страница: 81 / 180

Результаты поиска

Содержание 3450B - Phaser B/W Laser Printer

Отзывы: