Xerox 3450B - Phaser B/W Laser Printer Скачать руководство пользователя страница 71

Страница: 71 / 180

4-4

Phaser 3450 Laser Printer Service Manual

Front Panel Continually Displays “Output Tray Is Full”

Empty the output tray.

Ensure that the Output Full Actuator is in the correct position and moves without
binding.

Verify that all harness connections to the Output Full Sensor are secure.

Replace the Output Full Sensor.

Replace the Output Full Sensor Harness.

Replace the Exit Roller Assembly.

Replace the Main Board.

Paper Size Switch Assembly

Paper size and tray installation is determined by a combination of ON/OFF statuses of
the upper, middle, and lower switches of the Switch Paper Size Assembly.

Paper size

Switches

Upper

Middle

Lower

LEGAL14" ON

OFF

LEGAL13" ON

OFF

EXECUTIVE OFF

B5 OFF

OFF

A4 OFF

LETTER ON

OFF

A5 (for reference only, supported in Tray 1 only)

OFF

No Tray

OFF

Содержание 3450B - Phaser B/W Laser Printer





















































































































































































Результаты поиска

Содержание 3450B - Phaser B/W Laser Printer

Отзывы:

Xerox 3450B - Phaser B/W Laser Printer, Руководство по обслуживанию, Страница: 71 / 180

Результаты поиска

Содержание 3450B - Phaser B/W Laser Printer

Отзывы: