Xerox 3450B - Phaser B/W Laser Printer Скачать руководство пользователя страница 75

Страница: 75 / 180

4-8

Phaser 3450 Laser Printer Service Manual

Paper Mis-feed from Tray 3 (Optional Feeder)

Troubleshooting References

Procedure

Applicable Parts

Wiring and Plug/Jack Map References

Main Board

Tray 3 Assembly

Step

Action and Questions

Yes

Is paper loaded correctly?

Go to Step 2.

Load paper

correctly.

Is the tray damaged?

Are parts missing?

Replace Tray 3

Assembly.

Go to Step 3.

Is Tray 2 chute obstructed?

Clear

obstruction.

Go to Step 4.

Is the interface connector between the

printer and Tray 3 damaged?

Replace

interface

harness.

Go to Step 5.

Does Tray 3 Pick Roller rotate when the

Solenoid actuates? Refer to "Service

Diagnostics Menu Map" on page 3-9.

Go to Step 5.

Replace Tray 3

Assembly.

Are the feed roller or retard/drag pads dirty ? Clean if dirty.

Replace Tray 3

Assembly

Replace Main

Board.

Содержание 3450B - Phaser B/W Laser Printer





















































































































































































Результаты поиска

Содержание 3450B - Phaser B/W Laser Printer

Отзывы:

Xerox 3450B - Phaser B/W Laser Printer, Руководство по обслуживанию, Страница: 75 / 180

Результаты поиска

Содержание 3450B - Phaser B/W Laser Printer

Отзывы: