manualshive.com logo in svg

Xerox 3450B - Phaser B/W Laser Printer, Руководство по обслуживанию, Страница: 110 / 180

Поделиться
Скачать
Xerox 3450B - Phaser B/W Laser Printer Скачать руководство пользователя страница 110

Service Parts Disassembly

8-13

2.

Remove the Tray 1 Cover Assembly (page 8-10).

3.

Remove the Top Cover Assembly (page 8-9).

4.

Disconnect the Tray 1 Lift Plate Links from the Tray 1 Lift Plate by pulling 
outward on the end of the Link arms where they connect to the lift plate.

5.

Rotate each Link to align the key with the slot in the frame mounting hole and 
remove the Links.

6.

Remove the two screws securing the Front Cover to the printer, unlatch the two 
retaining hooks on each side, and remove the Front Cover.

Tray 1 Lift Plate (PL 9.1.3)

1.

Remove the Front (Inner) Cover (page 8-12).

2.

Disconnect the 2 Bias Springs from the metal frame.

Note

In some cases, the Bias Springs will slip off of the plastic mounting arms on 
the Lift Plate easily and they can be disconnected just as readily that way. 
However, there is less chance of damage when removing the springs from 
the metal frame.

3.

Remove the Tray 1 Lift Plate.

s3450-042

Содержание 3450B - Phaser B/W Laser Printer





















































































































































































Отзывы:

Нет отзывов