manualshive.com logo in svg

WORKMASTER GO-E2, Руководство оператора

Поделиться
Скачать
WORKMASTER GO-E2 Скачать руководство пользователя страница 14

 
 

PH: 866.476.9217 

13 

 

9.

 

Wire the control package to the Gear Motor. 

 

10.

 

The 

GO-E2

 Opener's Gear Motor is lubricated before shipment. Before start-

up (or prolonged storage), remove the seal from the breather/vent plug. The 

lubricant level should be checked with the 

GO-E2

 Opener mounted in its 

correct position. Lubricant should be added or removed to bring it to the 
correct level. 

 

11.

 

Test the Gear Motor by rotating the output shaft 360°. 

 

12.

 

Attach the motor-end yoke and Driveshaft assembly of the Telescoping 
Driveshaft to the Gear Motor; align the connection using the key/keyway 

provided on the Gear Motor, and firmly secure both set screws with a 3/16" 
Allen wrench. 

 

13.

 

Locate and mount the Electrical Control Box. The Control Console is housed in 

a NEMA-4 watertight steel enclosure with continuous hinge and cover clamps. 

 
 

 
 

 

 

 

 

 
 

 
 

 

 
 

 

 

 
 

IMPORTANT 

The Pushbutton Pendant Control Switch is 

supplied with 50' of 18/4SOOW portable 
cordage as standard. 

IMPORTANT 

A wiring diagram showing the motor circuit and 

the control circuit is attached inside the Control 
Box. 

Branch circuit conductors, disconnects, 

protection and grounding are the user's 
responsibility. Refer to Article 430 of the 

National Electrical Code. 

Содержание GO-E2









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды