manualshive.com logo in svg

WORKMASTER GO-E2, Руководство оператора

Поделиться
Скачать
WORKMASTER GO-E2 Скачать руководство пользователя страница 13

 
 

PH: 866.476.9217 

12 

 

4.

 

Once the W-Beam is secured, slide the BMA onto the beam so that the 
beam's top flange fits into the t-slot on the bottom of the BMA. 

 

5.

 

Slide the carriage to a spot on the W-Beam where it will be convenient to 

mount the Gear Motor. Once in position, lock the carriage in place by turning 

the t-handle set screws clockwise. 

 

6.

 

Place the gear motor on top of the BMA and using the hardware supplied, 
bolt the gear motor to the BMA. 

 

 

 

 
 

 
 

 

 

 

 

7.

 

With the Gear Motor completely secured, loosen the BMA's t-handle set 

screws and slide the unit back and forth along the beam to verify ease of 

movement. 

 

8.

 

Check the Gear Motor nameplate to verify that the phase, hertz and voltage 
agree with the available power source. 

 

 

 

 
 

 

 
 

 

 

 

 

 
 

CAUTION 

The E2 Opener's Gear Motor is designed to 
operate with the base mounted floor-

horizontal. Other special mountings require 

modifications to the lubrication system and 
seals. Consult your WORKMASTER Sales 

Representative on special mountings. 

CAUTION 

Although the control package includes overload 
protection, wiring the incorrect power supply 

could still damage the Gear Motor. Ratings 

cannot be exceeded. 

It is the purchaser's responsibility to determine 
the applicable local, state and national codes 

related to electrical wiring of this unit. 

Содержание GO-E2









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды